Potterton Solar Maintenance & Service Manual Download

Page: 29 / 32

Potterton Solar - Solar Thermal Domestic Hot Water System

6.0

Spares

6.1

Spare parts

A number of Spare Parts are available should any part of

the Potterton Solar system require replacement. Use only

genuine parts obtained from Potterton, use of other non

Potterton parts may cause system malfunctions and will

invalidate the warranty. Fitting of any spare parts must

be carried out by a competent installer or authorised

service engineer or agent.

Description

Code No.

A Roof bracket assembly (On roof panels)

(comprising roof bracket, roof bracket console,

cup square bolt M8 x 25, M8 washer, M8 hex self

securing nut and 2 off self tapping screws No6 x 60 long)

5119532

B Collector panels fixings kit (On roof panels)

(comprising 2 off No6 x 60 self tapping screws,

cup square bolt M8 x 25, M8 washer, M8 hex nut,

M8 self securing nut, M8 x 30 hammer head bolt,

mounting part top, clamping piece)

5119533

C Extension assembly (On roof panels)

(comprising clamping piece extension,

mounting part extension, 2 off M8 hex nut, 2 off M8 washer)

5119534

D Connection washer (On roof panels)

(comprising 2 off flat sealing washer)

5119535

E Temperature sensor

5119536

F Solar differential temperature controller

(complete)

5122978

G Pressure relief valve

5119538

H Pressure Gauge

5119539

Safety Group

(complete)

5119540

Solar primary circulating pump

5119541

K Flow meter assembly

5119542

L Temperature gauge

5119543

M Solar heat transfer fluid 10 litre drum

5119544

N Solar heat transfer fluid 20 litre drum

5119545

O Solar expansion vessel 24 litre

5119548

P Expansion vessel self-sealing connection

5119779

Q Flow Meter (for solar gain module)

5122979

R Sensor (for solar gain module)

5122980

S Connection washers (for in roof panels)

5122981

T Flexible connection hose (2m) + insulation

5122982

U Roof bracket kit for in roof panels

(comprising roof bracket, self tapping screws 5x60

sealed plumbing screws 4.5x35, metal retainer

and roofing nails)

5122983

V Connection adaptor for in roof panels

5122984

W 1

”

BSP male / 3/4

”

female adaptor fitting

5129783

X 1

”

BSP male / 3/4

”

male adaptor fitting

5129784

Y Thermostatic blending valve

5122985

NOTE:The solar cylinders have their own set of spare

parts available. Information on these can be found in the

separate cylinder installation instruction manual.

Summary of Contents for Solar

































Search results

Summary of Contents for Solar

Reviews:

Related manuals for Solar

Brands by name

Popular brands

Potterton Solar, Maintenance & Service Manual

Search results

Summary of Contents for Solar

Reviews:

Related manuals for Solar

Brands by name

Popular brands