Poulan Pro 190785 Owner'S Manual Download | Manualshive

Page: 41 / 44

background image

41

REPAIR PARTS

TRACTOR - - MODEL NUMBER PO15538B

MOWER DECK

KEY PART
NO. NO. DESCRIPTION

1   170280     Mower Housing Assembly
2   72140506     Bolt Carriage 5/16-18 x 3/4
3   138017     Bracket Asm Fr. Sway Bar
4   169970     Bracket Deck Sway Bar 38"/42"
5   4939M   Retainer Spring
6   178024     Bar Sway Deck
8   850857     Bolt 3/8-24 x 1.25 Gr. 8
9   10030600     Washer, Lock 3/8
10   140296     Washer, Hardened
11   138497     Blade Mower
13   137645     Shaft Assembly, Mandrel, Vented

(Includes Key Number 6)

14   128774     Housing, Mandrel, Vented
15   110485X   Bearing, Ball, Mandrel
16   174493     Stripper, Vented Mower Deck
19   132827     Bolt, Shoulder
21   73680500     Nut
23   137607     Bracket, Mower Defl ector
24   105304X   Cap, Sleeve
25   123713X   Spring, Torsion, Defl ector
26   110452X   Nut, Push
27   106736X428  Shield, Defl ector
28   19111016     Washer 11/32 x 5/8 x 16 Ga.
29   106735X   Rod, Hinge
30   173984     Screw Thdrol.
31   187690     Washer, Spacer
32   153532     Pulley, Mandrel
33   178342     Nut, Toplock
36   131494     Pulley, Idler, Flat
40   73680600     Nut, Crownlock 3/8-16 unc
45   4497H   Retainer
53   130840     Brake Assembly

54   178515     Washer, Hardened
55   133840     Idler Arm Assembly
56   165723     Spacer, Retainer
67   106932X   Knob
68   144200     V-Belt, 42" Mower
86   7631J     Runner, LH
87   128772     Runner, RH
88   19111216     Washer 11/32 x 3/4 x 16 Ga.
89   19131311     Washer 13/32 x 13/16 x 11 Ga.
96   74930620     Bolt 3/8-16 x 1-1/4 Mulcher
97   73930600     Nut Centerlock 3/8-16 unc
107   133502     Spacer Retainer
108   133503     Stiffener, Idler Arm
109   74760640     Bolt, Hex Hd 3/8-16 x 2-1/2
110   142587     Upstop Deck Front 38"
113   17060512     Screw 5/16-1/ x 3/4
122   131289     Rod, Brake LH
123   169971     Rod, Brake RH
146   165891     Bolt Carriage Idler
148   169022     Spring Return Idler
149   165898     Retainer Spring Yellow
150   19091216     Washer 9/32 x 3/4 x 16 Ga.
152   172758     Clutch Cable 38"/46"
158   17720408     Screw Hex Thd Cut 1/4-20 x 1/2
185   188234     Head Asm Cable Clutch
- -      130794     Mandrel Assembly (Includes Hous-

ing, Shaft and Shaft Hardware Only
- Pulley Not Included)

- - 170317 Replacement Mower, Complete

KEY PART
NO. NO. DESCRIPTION

NOTE:

All component dimensions given in U.S. inches

1 inch = 25.4 mm

«
...
39
40
41
42
43
...
»

Summary of Contents for 190785













































Reviews:

No comments

Related manuals for 190785

Brand: Tanaka Pages: 8

Brand: Ferris Pages: 44

Brand: Yard force Pages: 16

Brand: Redexim Pages: 12

Brand: Yazoo/Kees Pages: 30

Brand: Poulan Pro Pages: 48

Brand: Toro Pages: 28

Brand: Alamo Industrial Pages: 186

Brand: Garland Pages: 172

Brand: Walker Rider Lawnmowers Pages: 100

Brand: Yazoo/Kees Pages: 84

Brand: Electrolux Pages: 13

Brand: Electrolux Pages: 11

Brand: Electrolux Pages: 13

Brand: Electrolux Pages: 11

Brand: Electrolux Pages: 11

Brand: Electrolux Pages: 15

Brand: Tramontina Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands