background image

13

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR 
TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of 
various controls and ad just ments.  Save this manual for future reference.

Our tractors conform to the safety standards of the 

American National Stan dards Institute. 

ATTACHMENT CLUTCH SWITCH 

-

 

Used 

to engage the mower blades, or other at-
tachments mounted to your trac tor.

LIGHT SWITCH

 

POSITION 

- Turns the 

head lights on and off.

THROTTLE CONTROL

 - 

 

Used to con trol 

engine speed.

BRAKE PEDAL

 - Used for braking the 

tractor and starting the engine.

CHOKE CONTROL

 - Used when start ing 

a cold engine.

HEIGHT ADJUSTMENT KNOB

 - Used to 

adjust the mow er cutting height. 

IGNITION SWITCH

 - Used for starting and 

stopping the engine.

ATTACHMENT LIFT LEVER

 - Used to raise 

and lower the mower deck or other at tach ments 
mounted to your tractor.

LIFT LEVER PLUNGER

 - Used to re lease 

attachment lift lever when chang ing its 
position.

AMMETER

 - Indicates charging (

+

) or 

discharging (

-

) of battery.

PARKING BRAKE LEVER

 - Locks brake 

pedal into the brake po si tion.

MOTION CONTROL LEVER 

- Selects the 

speed and direction of tractor.

FREEWHEEL CONTROL 

- Disengages 

transmission for pushing or slowly towing 
the tractor with the engine off.

MOTION DRIVE BELT TENSION HAN-
 DLE 

- Used when changing motion drive 

belt and, if necessary, starting engine 
under extremely cold conditions.

02507

Light Switch 
Position

Lift 
Lever 
Plunger

Attachment 
Lift Lever

Parking Brake 
Lever

Motion Control 
Lever

Height 
Adjustment 
Knob

Ignition 
Switch

Attachment 
Clutch Switch

Ammeter

Choke 
Control

Throttle 
Control

Brake Pedal

Free Wheel 
Control

Approx. 
Speed:
3MPH
2MPH
1MPH

Motion Drive 
Belt Tension 
Handle

Summary of Contents for 191491


































Reviews: