background image

14

02149

Attachment Clutch 
Switch Pull Out to 
“Engage” 

Push-In to 
“Disengage”

Throttle 
Control

Motion 
Control 
Lever

Choke 
Control

TO USE THROTTLE CON TROL 

Always operate engine at full throttle.
•   Operating engine at less than full 

throttle reduces the battery charg ing 
rate.

•   Full throttle of fers the best mower per-

 for mance.

TO USE CHOKE CONTROL 

Use choke control whenever you are start-
ing a cold engine. Do not use to start a 
warm engine.
•   To engage choke control, pull knob out.  

Slowly push knob in to dis en gage.

Brake 
Pedal

Brake Pedal 
“Drive” Position

Height 
Adjustment 
Knob

“Disengaged” 
Position

Parking Brake 
“Engaged” 
Position

Ignition 
Key

TO MOVE FORWARD AND 
BACKWARD 
CAUTION:

 Do not attempt to operate mo-

tion control lever when the parking brake 
is set or when the brake pedal is de-
pressed. Doing so may result in misadjust-
ment to the drive con trol system.
The direction and speed of movement is 
controlled by the motion control lever.
1.   Start tractor with motion control le ver in 

neutral (N)  position.

2.   Release parking brake.
3.   Slowly move motion control lever to 

desired position. 

00155

The operation of any tractor can  result in foreign objects thrown into 
the eyes, which can result in severe eye dam age.  Always wear safety 
glass es or eye shields while operating your tractor or per form ing any 
ad just ments or repairs.   We rec om mend standard safety glasses or a 
wide vision safety mask worn over spectacles.

HOW TO  USE YOUR TRAC TOR

TO SET PARKING BRAKE 

Your tractor is equipped with an operator 
presence sens ing  switch.  When engine 
is running, any attempt by the op er a tor 
to leave the seat without fi rst setting the 
parking brake will shut off the engine.
1.   Depress brake pedal all the way down 

and hold.

2.   Pull parking brake lever up and re lease 

pres sure from brake pedal.  Pedal 
should re main in brake po si tion.  Make 
sure parking brake will hold tractor 
secure.

TO ADJUST MOWER CUT TING HEIGHT

The cutting height is controlled by turn-
 ing the height ad just ment knob in desired 
direction.
•   Turn knob clockwise (

 ) to raise cut-

ting height.

•   Turn  knob  counterclockwise (

 ) to  

lower cutting height.

STOPPING 

MOWER BLADES -
•   To stop mower blades, push at tach ment 

clutch switch in to disengaged position.

GROUND DRIVE -
•   To stop ground drive, depress brake 

pedal all the way down.

IMPORTANT:

 The motion control lever 

returns to neutral (N) position when the 
brake pedal is fully depressed.

ENGINE - 
•   Move throttle control to slow po si tion.

NOTE:

  Failure to move throttle control to 

slow position to allow engine to idle before 
stopping may cause engine to “back fi re”.
•   Turn ignition key to “STOP” position and 

remove key.  Always remove key when 
leaving tractor to prevent un au tho rized 
use.

•   Never use choke to stop engine.

IMPORTANT: 

 Leaving the ignition switch 

in any position other than "STOP" will 
cause the battery to discharge and go 
dead.

NOTE:

  Under certain conditions when 

tractor is standing idle with the engine 
running, hot engine exhaust gases may 
cause “browning” of grass.  To elim i nate 
this possibility, always stop en gine when 
stopping tractor on grass areas.

CAUTION:

  Always stop tractor com-

 plete ly, as de scribed above, before leav ing 
the operator's position.

Summary of Contents for 191491


































Reviews: