background image

10

OPERATION

TO ADJUST MOWER CUT TING HEIGHT  
(See Fig. 8)

The po si tion of the at tach ment lift le ver (A) de ter mines the 
cut ting height.

•      Put attachment lift lever in desired cutting height slot.
•     Slide pointer tab (T) to desired cutting height as a 

reminder for next time you mow.

The cutting  height  range is  ap prox i mate ly 1" to  4".  The 
heights are measured from the ground to the blade tip with 
the engine not running.  These heights are approximate and 
may vary depending upon soil conditions, height of grass 
and types of grass being mowed.
•         The average lawn should be cut to approximately 2-1/2 

inches during the cool season and to over 3 inches 
during hot months.  For healthier and better looking 
lawns, mow often and after moderate growth.

•     For best cutting performance, grass over 6 inches 

in height should be mowed twice.  Make the fi rst cut 
relatively high; the second to de sired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels  are prop er ly ad just ed when they are slight ly 
off the ground when mower is at the desired cutting height 
in operating position. Gauge wheels then keep the deck 
in proper position to help prevent scalping in most terrain 
conditions. 

NOTE:

 Adjust gauge wheels with tractor on a fl at level 

surface.
•      Adjust mower to desired cutting height (See “TO AD-

 JUST MOWER CUT TING HEIGHT” in this sec tion of 
manual).

•     With mower in desired height of cut po si tion, gauge 

wheels should be assembled so they are slightly off 
the ground. In stall gauge wheel in ap pro pri ate hole. 
Tighten se cure ly.

•      Repeat for all, installing gauge wheel in same adjust-

ment hole.

FIG. 8

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing 
switch.  Any attempt by the operator to leave the seat with 
the engine running and the attachment clutch engaged 
will shut off the engine. You must remain fully and centrally 
positioned in the seat to prevent the engine from hesitating 
or cutting off when operating your equipment on rough, 
rolling terrain or hills.
•      Select desired height of cut with attachment lift lever.
•     Start mower blades by engaging at tach ment clutch 

control.

TO STOP MOWER BLADES - 
disengage at tach ment clutch con trol.

CAUTION:  Do not operate the mower 
without either the en tire grass catcher, 
on mowers so equipped, or the defl ector 
shield (S) in place.

S

FIG. 10

J

FIG. 7

TO MOVE FORWARD AND BACKWARD 
(See Fig. 7)

The direction and speed of movement is controlled by the 
motion control lever. (J)
•     Start tractor with motion control le ver in neutral (N)  

position.

•      Release parking brake.
•      Slowly move motion control lever to desired position. 

A

T

Summary of Contents for 404378































Reviews: