background image

7

ASSEMBLY

FIG. 2

NOTE: 

You may now roll or drive your tractor off the skid. 

Follow the appropriate instruction below to remove the 
tractor from the skid.

  WARNING:

 Before starting, read, un der stand and follow 

all in struc tions in the Operation section of this manual. Be 
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID  (See Op-
 er a tion section for location and func tion of 
con trols)

•      Press lift lever plunger and raise attachment lift lever 

to its highest po si tion.

•      Release  parking  brake  by  depressing  clutch/brake 

ped al.

•      Place gearshift lever in neutral (N) po si tion.
•      Roll tractor forward off skid.
•     Remove banding holding defl ector shield up against 

tractor.

TO DRIVE TRACTOR OFF SKID (See Op-
 er a tion sec tion for lo ca tion and func tion of 
con trols)

•      Be sure all the above assembly steps have been com-

pleted.

•      Check engine oil level and fi ll fuel tank with gasoline.
•      Sit on seat in operating position, depress clutch/brake 

pedal and set the parking brake.

02466

02464

SEAT PAN

SHOULDER 
BOLT

ADJUSTMENT 
KNOB

FLAT WASHER

SEAT

02602

CONNECT BATTERY (See Figs. 3 and 4)

CAUTION:  Do not short battery termi-
nals by allowing a wrench or any other 
object to contact both terminals at the 
same time.  Before connecting battery, 
remove metal bracelets, wristwatch 
bands, rings, etc. 

Positive terminal must be connected 
fi rst to prevent sparking from accidental 
ground ing. 

•      Lift seat pan to raised position.
•      Remove terminal protective caps and discard.
•      If this battery is put into service after month and year 

indicated on label (label located between terminals) 
charge battery for minimum of one hour at 6-10 amps. 
(See "BATTERY" in the Maintenance section of this 
manual for charg ing in struc tions).

•         First connect RED battery cable to positive (+) terminal 

with hex bolt and keps nut as shown.  Tighten securely. 
Slide terminal cover over terminal.

•     Connect BLACK grounding cable to negative (-) ter-

minal with remaining hex bolt and keps nut.  Tighten 
securely. 

02604

FIG. 3

FIG. 4

HEX BOLT

NEGATIVE (BLACK) 
CABLE

POSITIVE (RED) 
CABLE

KEPS 
NUT

SEAT PAN

TERMINAL 
COVER

DISCARD TER MI NAL 
PROTECTIVE CAPS

LABEL

Summary of Contents for LAWN TRACTOR PE12538LT













































Reviews: