background image

-- 12 --

TROUBLE

CAUSE

REMEDY

Engine will not

start.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching

carburetor.

5. Compression low.

1. See “Starting a Flooded Engine”

in Operation section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer.

Engine will not

idle properly.

1. Fuel not reaching

carburetor.

2. Carburetor requires

adjustment.

3. Crankshaft seals worn.

4. Compression low.

1. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

2. See “Carburetor Idle Speed Adjustment”

in Service and Adjustments Section.

3. Contact an authorized service dealer

4. Contact an authorized service dealer.

1. Air filter dirty.

2. Fuel not reaching

carburetor.

3. Spark plug fouled.

4. Carburetor requires

adjustment.

5. Carbon build up.

6. Compression low.

Engine will not

accelerate,

lacks power, or

dies under a

load.

1. Clean or replace air filter.

2. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

3. Clean or replace spark plug

and re-gap.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

6. Contact an authorized service dealer.

Engine smokes

excessively.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact an authorized service dealer.

Engine runs hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build up.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

TROUBLESHOOTING TABLE

WARNING:

Always stop unit and disconnect spark plug before performing any of the

recommended remedies below other than remedies that require operation of the unit.

Summary of Contents for Pro BVM210VS















Reviews: