USB
Automatic Distance Function
Calories Burned
5
Electronic Braking System
The Electronic Braking System is an optional extra within the Freeway Range. The EBS
has the added advantage of an Electronic Braking System (EBS) for hill decent control
thus creating the ultimate machine for all conditions.
To activate the braking function:
1: Ensure the motor and power is on.
2: Rotate the control knob counter-clockwise until you go below zero. The EBS logo
will appear next to the power setting to indicate the braking function, which will display
between 1, 2 and 3 indicating the level of braking force being applied, 3 being the
highest.
3: Rotate the control knob clockwise to return to normal power settings.
Note: you do not have to pause the trolley between the standard power and EBS
braking mode
WARNING!
EBS is an assisted braking system for hill descent not a 100% parking brake. The trolley must be powered on and the
wheels engaged with the clutch for the braking system to function. The drive system uses a limited slip differential to allow braking
and provide ease of manoeuvrability. Try to avoid traversing a steep hill as the load of the trolley will mostly be applied to the lower
wheel on the slope, and may cause the higher wheel to slip. If your trolley loses traction and the wheels start to spin apply more even
pressure on the handle to increase traction of both wheels. Engage the braking progressively as you descend a slope.
Caution:
Wet or loose ground can cause the wheels to lock and slip on steep slopes. When using the maximum braking force
always maintain a firm grip on the handle to assist the trolley and avoid injury or damage.
EBS symbol indicates braking function active
Security Pin:
With the padlock icon highlighted you can turn the PIN function on and
off by pressing the central control knob. To select your security PIN rotate the control
knob to select your 4 digit code, save each digit by pressing the control knob. Repeat
for each digit and then press and hold both buttons to save the new PIN.
Note: if you have added a PIN lock this will be required every time you turn the trolley
on. In the event you have forgotten your PIN you can use the default factory PIN:
7921
to unlock the controls.
Distance Measurement Preference:
This will change the type of measurement and
ADF functions from yards (miles) to metres (Km). Push the Central Control Knob to
select either option.
Pin Function
Distance Units
Clock
Competition Mode
Battery Gauge
S/N: A
Your PowaKaddy trolley is simple to maintain.
Never jet wash your trolley or immerse into water. Occasionally remove the wheels and apply grease to the axle and moving parts.
Your serial number can be found on the underside of the main body chassis. Keep a note of the serial number for reference in the
box provided above.
Maintenance
Understanding the Battery Gauge:
The battery gauge on the FW7s is similar to a car fuel gauge - F (full), ½ (half full) & E
(empty). There are five blue bars and depending on the charge state of your battery
will determine how many bars illuminate. When a fully charged battery is connected to
the trolley all five blue bars will illuminate.
As you progress through your round the blue bars will extinguish from full to empty.
When the fifth blue bar is extinguished it indicates that the battery is flat. When your
battery is new you may lose only one or two bars during the entire round. As your
battery ages, you may lose more bars.
If you lose all the blue bars this could indicate; (1) you have not fully charged your
battery (2) your battery is nearing the end of its useful life and you should consider
buying a replacement.
Automatic Distance Function (ADF):
The ADF function is a convenient way of sending your trolley a set distance. (15, 30, 45 yards
or meters) For example when you are approaching a green you can send the trolley towards
the next tee if the route allows. Please note it is not recommended to send your trolley
unattended over steep or rough terrain. To activate when trolley is in pause mode:
1: Press and hold the central control knob until ‘ADF’ appears on the display
2: Rotate the control knob to select the distance required between 15-45 Yrds/Metres.
3: To start the function press the control knob.
4: To cancel rotate the Central Control Knob to “00” and select by pressing the control knob.
WARNING!
Before using the ADF function please ensure the route is clear from any
obstacles. To interrupt the distance function when in operation press the on/off
button to stop the motor function.
**Please note ADF distance are approximate based on flat level terrain conditions using a fully charged battery. The overall
distance may be affected by terrain conditions, obstacles or incline, battery power and weight of golf bag.
Factory Settings
Your new FW7s trolley is ready to use, but there are a number of preferences you can
change in the programming mode. To enter programming mode:
1: Connect the battery to the trolley.
2: With the trolley powered and the default display shown press and hold both function
buttons for 3 seconds. The main features on the display will be replaced by the clock
flashing in the top left hand corner of the display.
3: Press the right function button to scroll through the options.
4: Select or modify the option by pressing the central control knob, then use the dial to
adjust the setting or input values.
5: Press and hold both function buttons to save and exit after changing any settings. The
display will then return to the default display.
Each of the Factory Settings are detailed below:
Time:
With the clock flashing rotate the control knob to the required digit and press to
save each digit.
COMP Mode:
With `COMP’ highlighted on the display press the control knob to turn the
‘competition’ mode on and off. This will disable ADF, distance functions and calories
measurement.
00937-01-08 Freeway Instruction Booklet.indd 6-7
18/01/2018 13:05:50
