background image

Powered by Safety

®

2

General Information

01.4IB.51809

Electric Remote Racking Device for  

Powell LV Switchgear w/ Siemens Circuit Breakers

A.  S

cope

The information in this instruction bulletin 

describes the following Remote Racking 

Devices for Powell version Siemens LVAR 

Racking Device:

•  51897G31 - 800, 1600, 2000, 3200, 4000, &    

 5000

B.  p

urpoSe

The information in this instruction bulletin is 

intended to provide information required to 

properly operate and maintain the  

Powell version Siemens LVAR Racking Devices 

described in 

Ch 1 General Information,

  

A. S

cope

.

This instruction bulletin provides:

1.  Safety guidelines

2.  General descriptions on the operation of 

the

 

Powell version Siemens LVAR Racking 

Device

3.  Instructions for installation

4.  Illustrations, photographs, and description 

of the equipment described in  

Ch 1 General Information

A. S

cope

.

The illustrations in this document are provided 

as general information to aid in showing 

component locations only.  

All photos and illustrations are shown using 

deenergized equipment.

Be sure to follow the appropriate safety 

precaution while handling any of the 

equipment.  Failure to do so may result in 

serious injury or death.

!

WARNING

To the extent required, the products described 

herein meet the applicable ANSI, IEEE, and 

NEMA Standards; however, no such assurance 

is given with respect to local codes and 

ordinances which may vary greatly.

c.  I

nStructIon

 B

ulletInS

 A

vAIlABle

 e

lectronIcAlly

Changes to the instruction bulletin may be 

implemented at any time and without notice.  

Goto www.powellind.com to ensure use of 

the current instruction bulletin for the Powell 

equipment.

NOTICE

To contact the Powell Service Division call 

1.800.480.7273 or 713.944.6900, or email  

info@powellservice.com.

For specific questions or comments pertaining 

to this instruction bulletin email  

documents@powellind.com with the 

Instruction Bulletin number in the subject line.

Summary of Contents for 51897G31-1600
























Reviews: