background image

Ch 1  General Information

Powell reserves the right to discontinue and to change specifications at any time without incurring 

any obligation to incorporate new features in products previously sold.

IMPORTANT

IMPORTANT

!

Powered by Safety

®

1

General Information

SM-1500

WARNING

WARNING

!

The equipment described in this document may contain high voltages and currents which can 

cause serious injury or death.

The equipment is designed for use, installation, and maintenance by knowledgeable users of such 

equipment having experience and training in the field of high voltage electricity.  This document 

and all other documentation shall be fully read, understood, and all warnings and cautions 

shall be abided by.  If there are any discrepancies or questions, the user shall contact Powell 

immediately at 1.800.480.7273.

WARNING

WARNING

!

Before any adjustment, servicing, part replacement, or any other act is performed requiring 

physical contact with the electrical working components or wiring of this equipment, the power 

supply must be disconnected.  Failure to follow this warning may result in injury or death.

Courtesy of NationalSwitchgear.com

Summary of Contents for SM-1500

















Reviews: