background image

UK Helpline 0905-1460005 • Ireland Helpline 1520-932626

Web Support: www.servotool.eu

Model Number: PKB-1050/2 

 

 

 

 

 

7

Safety instructions

3)  Personal safety
a.  Stay alert, watch what you are doing and use common sense when 

operating a power tool. Do not use a power tool while you are tired 
or under the influence of drugs, alcohol or medication.  A moment of 
carelessness while operating power tools may result in serious personal 
injury.

b.  Use safety equipment. Always wear eye protection. Safety equipment 

such as dust mask, non-skid safety shoes, hard hat, or hearing protection 
used for appropriate conditions will reduce personal injuries.

c.  Avoid accidental starting. Ensure the switch is in the off position before 

plugging in. Carrying power tools with your finger on the switch or 
plugging in power tools that have the switch on invites accidents.

d.  Remove any adjusting key or wrench before turning the power tool on. 

A wrench or a key left attached to a rotating part of the power tool may 
result in personal injury.

e.  Do not overreach. Keep proper footing and balance at all times. This 

enables better control of the power tool in unexpected situations.

f.  Dress properly. Do not wear loose clothing or jewellery. Keep your hair, 

clothing and gloves away from moving parts. Loose clothes, jewellery or 
long hair can be caught in moving parts.

g.  Use clamps or a vice to hold work. It’s safer than using your hand and it 

frees both hands to operate tool.

4)  Power tool use and care
a.  Do not force the power tool. Use the correct power tool for your 

application. The correct power tool will do the job better and safer at 
the rate for which it was designed.

b.  Do not use the power tool if the switch does not turn it on and off. Any 

power tool that cannot be controlled with the switch is dangerous and 
must be repaired.

c.  Disconnect the plug from the power source before making any 

adjustments, changing accessories, or storing power tools. Such 
preventive safety measures reduce the risk of starting the power tool 
accidentally.

d.  Store idle power tools out of the reach of children and do not allow 

persons unfamiliar with the power tool or these instructions to operate 
the power tool. Power tools are dangerous in the hands of untrained 
users.

Summary of Contents for 1050W





















Reviews: