The environment
In order to prevent damage during shipping, the device is delivered in sturdy packaging. The
packaging largely consists of recyclable materials. You should therefore use this opportunity to
recycle the packaging.
Damaged and/or disposed of electrical or electronic devices must be dropped off at
recycling stations intended for that purpose.
Warranty
Read the warranty conditions on the separately supplied warranty card.
Wear of the screw bits is not covered under the warranty.
CE
CONFORMITY DECLARATION (GB)
Bearing sole responsibility, we declare that this PCD-2400I conforms to the following standards
or guidelines:
EN60745-1, EN60745-2-1, EN60745-2-2, EN55014-1, EN55014-2, EN60335-1,
EN60335-2-29, EN61000-3-2, EN61000-3-3.
as per the stipulations in guidelines:
98/37/EC, 73/23/EEC, 89/336/EEC, 2002/95/EC, 2002/96/EC
from 01-10-2006
ZWOLLE NL
J.A. Bakker - van Ingen
J. Lodewijk
CEO Ferm BV
Quality Manager Ferm Global
It is our policy to continuously improve our products and we therefore reserve the right to
change the product specification without prior notice.
Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • The Netherlands
UK Help Line: 0870 - 7323023 / IRELAND Help Line: 1800-481005 - Powercraft
11
General Safety Rules
WARNING! Read all instructions. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed
below refers to your battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work
area
a.
Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gasses or dust. Power tools create sparks which may ignite the dust of
fumes.
c.
Keep children and bystanders away while operating a power tool. Distractions can cause
you to loose control.
2) Electrical
safety
a.
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or
grounded.
c.
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e.
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock. Always use tool in
conjunction with a residual circuit breaker device.
3) Personal
safety
a.
Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious
personal injury.
b. Use safety equipment. Always wear eye protection. Safety equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing protection used in appropriate
conditions will reduce the risk of personal injury.
c.
Avoid accidental starting. Ensure the switch is in the off position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that have the
switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e.
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of these devices can reduce dust
6
UK Help Line: 0870 - 7323023 / IRELAND Help Line: 1800-481005 - Powercraft
GB
F
E
P
I
S
SF
N
DK
GB