background image

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerfl opumps.com

20

LIMITED WARRANTY

Manufacturer warrants, to the immediate purchaser and subsequent initial owner during the warranty period, 

every new pump to be free from defects in material and workmanship under normal use and service, when properly 

used and maintained, for a period of eighteen (18) months from date of manufacture or twelve (12) months from 

date of installation (which ever comes fi rst). Failure due to wear due to excessive abrasives is not covered. The 

initial owner is the purchaser who fi rst uses the pump after its initial installation, or for non-permanent installation, 

the fi rst owner who uses the pump. The date of installation shall be determined by a dated sales receipt noting the 

model and serial number of the pump. The dated sales receipt must accompany the returned pump. Product will be 

repaired, replaced or remanufactured at Manufacturer’s option. No allowance will be made for shipping charges, 

damages, labor or other charges that may occur due to product failure, repair or replacement. This warranty does 

not apply to and there shall be no warranty for any material or product that has been disassembled without prior 

approval of Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident or act of God; that has 

not been installed, operated or maintained in accordance with Manufacturer’s installation instructions; that has 

been exposed to outside substances including but not limited to the following: sand, gravel, cement, mud, tar, 

hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive substances, wash 

towels or feminine sanitary products, etc. in all pumping applications. The warranty set out in the paragraph above 

is in lieu of all other warranties expressed or implied; and we do not authorize any representative or other person 

to assume for us any other liability in connection with our products. Contact Manufacturer at:  1-877-24PUMPS or 

www.powerfl opumps.com, Attention: Customer Service Department, to obtain any needed repair or replacement 

of part(s) or additional information pertaining to our warranty. 

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL

DAMAGES OR BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS 

FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE 

EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, so the above limitation may not apply 

to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above 

limitation or exclusion may not apply to you. This warranty gives you specifi c legal rights and you may also have 

other rights which vary from state to state.

PFG - HH & HV 2HP 

 

 

 

  

                   Submersible Grinder Pumps

BACK TO INDEX

Summary of Contents for PFG2002HH





















Reviews: