background image

 

 

POWERKING                                                    1-800-344-3371                              SUPPORT@QVTOOLS.COM 

Shipping 
Dimensions 

25”x17”x44” 

 
Chipper Operation 

 

All branches should not exceed 3in diameter. Fresh cut branches and straw are 
recommended for best performance. Due to different hardness and moisture content, the 
engine may struggle but will continue to chip. Proper insertion of branches is large 
diameter to smaller diameter. It is best to put branches with leaves all together. Small 
logs are not recommended. 
 

Procedure 

1.

 

Make sure chipper is on flat dry surface. 

2.

 

Adjust exit chute to location for processed material. 

3.

 

Refer to Kohler manual on how to start the engine. 

4.

 

Adjust throttle to maximum RPM. 

5.

 

Do not stand directly behind entry chute. Stand to the side of entry chute as 
material may kick back. 

6.

 

Load material from large diameter side. 

7.

 

When machine starts to auto-feed, let go of branch.  

8.

 

Let it completely process material before adding more. 

9.

 

If machine does not auto-feed, you may need to slowly load the branches or use 
other branches to guide it in. 

 
Maintenance 

Regular maintenance is the way to ensure the best performance and long life of your 
machine. Please refer to this manual for proper maintenance procedures. 
 

 

Before performing any maintenance procedure or inspection, stop the motor, unplug the 
power cord and wait 5 minutes to allow all parts to cool. Disconnect the spark plug wire 
to prevent accidental startup.  

 

Summary of Contents for PK0913














Reviews: