background image

Limited Warranty 

Power Modules  Inc., herein referred to as the “manufacturer”, guarantees

this product to be free from defect in both material and workmanship, and agrees to
remedy any such defect or replace any defective component at no charge for a
period of five years from the date of sale to the first end user. This warranty is void
if the product has been found to be subjected to misuse, abuse, lightning strike,
unauthorized service, damaged in transit, or has been altered or repaired in such a
way so as to detract from its performance, reliability, or its safe operation.  

Should such a defect be discovered and it falls within the terms of this guar-

antee, the manufacturer will correct the defect in workmanship and/or replace any
defective component with a new one of similar capability and value. This warranty
does not apply to the cabinet or appearance items such as the faceplate, control
knobs, or meter lenses, nor does it cover any expenses incurred in shipping the
unit to the appropriate service depot.  

The foregoing is in lieu of any other warranties expressed, implied, or statu-

tory and the manufacturer neither assumes nor authorizes any person to assume
for it any other obligation or liability in connection with the sale of this product. This
warranty is not transferable except by written authorization from the manufacturer.  

In order to qualify under the terms of the above warranty, all items must be

returned to the appropriate factory service depot with all shipping charges prepaid.
In lieu of having previously registered the purchase of the unit by completing and
returning the attached Purchase Registration Card, the unit must be accompanied
by proof of purchase (bill of sale) from an authorized Power Modules dealer. 

Power Modules  Inc. 
Please Note: Defective units must be returned to the selling dealer or to Power
Modules at their service depot within the country of sale. 

The shipping address is:  Power Modules Inc. 479 East St. Pittsford, N.Y. 14534
Phone Number:     (585) 586-0740 

Warning 
TO PREVENT SHOCK OR HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO
NOT REMOVE COVER OR FACEPLATE. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING  TO QUALIFIED SERVICE PERSONNEL.

Model No. _________________________ Ser No.______________________ 

Purchased From _____________________________  On ___________________

(Name of Dealer)

(Date)

Summary of Contents for Belles 350A Reference










Reviews: