background image

 

POWX354 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

7

 

www.varo.com 

6.4 

Spray Technique 

 

The spray result depends heavily on the smoothness and cleanliness of the surface to be 
sprayed. Therefore the surface should be carefully prepared and kept free of dust. 

 

Cover all surfaces not to be sprayed.  

 

Cover screw threads or similar parts of the target object. 

 

It is advisable to test the spray gun on cardboard or a similar surface to find the correct 
setting. 

Important: Begin spraying outside of the target area and avoid interruptions 
inside the target area. 

 

Correct (Fig. 6a): Be sure to hold the spray gun at an even distance of approx. 10 

– 30 cm 

to the target object. 

 

Incorrect (Fig. 6b): Heavy spray fog build-up, uneven surface quality. 

 

Move the spray gun evenly cross-wise or up-and-down, depending on the spray pattern 
setting. 

 

An even movement of the spray gun results in an even surface quality. 

 

 

When coating material builds up on the nozzle (A) and air cap (B) (Fig. 7), clean both parts  
with a solvent or water. 

6.5 

Interruption of work up till 4 hours max. 

 

Turn the machine off.  

 

When processing 2-component varnishes, clean the device immediately. 

7  TAKING OUT OF OPERATION AND CLEANING 

Proper cleaning is the prerequisite for problem-free operation of the paint application device. 
No warranty claims are accepted in case of improper or no cleaning. 

 

Unplug the power plug. Vent the container in case of longer breaks and after the work has 
been terminated. This can be done by briefly turning open and then closing the container 
or by pulling the trigger guard and letting the paint into the original paint container. 

 

Divide the spray gun. Press the unlock button (Fig. 8 A) downwards.  

 

Unscrew the container. Empty any remaining coating material back into the material tin. 

 

Preclean the container and suction tube with a brush. 

 

Pour solvent or water into the container. Screw the container back on. Use only solvents 
with a flashpoint over 21 °C . 

 

Assemble the gun again.  

 

Insert the power plug, turn on the machine and spray the solvent or water into a container 
or a cloth.  

 

Repeat the above procedure until the solvent or water emerging from the nozzle is clear. 

 

Turn of the machine and remove the plug.  

CAUTION!  Never  clean  seals,  diaphragm  and  nozzle  or  air  holes  of  the 
spray gun with metal objects.  

The  ventilation  hose  and  diaphragm  are  only  solvent-resistant  to  a  limited 
extent. Do not immerse in solvent, only wipe. 

WARNING!  Never  hold  the  spray  gun  rear  part  under  water  or  immerse  it 
into liquids. Clean the housing only with a moistened cloth.  

 

 

Summary of Contents for POWX354












Reviews: