background image

expensive filtration. The tip seal should
be replaced every 10,000 hours of oper-
ation.

1. Confirm if the tip seal you pur-

chased is correct for the air end you
are repairing (See Parts Listing
below).

2. Confirm if the following parts are 

included (See Figure 6).

1. Remove six nuts with T-type wrench

and then FS set from air end (See
Figure 7).

2. Remove LP and HP tip seals from

Fixed Scroll set and Orbit set. Using
the tip of a ball-point pen at the
start will make it much easier (See
Figure 7).

3. Remove dust from Scroll with clean

cloth or air.

Figure 7

Scroll Air Compressors

4

NOTE: 

In order to distinguish between the tip seal for Fixed Scroll and the tip seal for Orbit Scroll place the tip seal as

shown below then view from the arrow direction and refer to the figure on the right.

Orbit Scroll

Fixed

Scroll

Facing

Right

Facing 
Left

Lip

(Bottom Side)

Lip
(Inside)

Per OSHA
regulations, ALL

power must be locked out before per-
forming any maintenance.

The “Tip Seal Set” is a replacement
part for SLAE03 and SLAE05 air ends.
Please read these instructions thor-
oughly and carefully to ensure correct
replacement.

NOTE:

Replace tip seal on SLAE03HP

and SLAE50HP at 5,000 hours when
operated at 145 psig.

(See Scroll Service and
Maintenance Video for Audio and
Visual Instructions.)

The tip seal on the scroll compressor is
self-lubricated and allows the unit to
operate efficiently without oil and

!

WARNING

Tip Seal Set
Replacement

10,000 HOURS - MAINTENANCE

CONFIRMATION OF THE PARTS

REPLACEMENT

Item

No.

Description

Qty.

1

HP tip seal for FS

1

2

LP tip seal for FS

1

3

HP tip seal for OS

1

4

LP tip seal for OS

1

5

Dust Seal

1

6

Backup Tube

1

HP = High Pressure

LP = Low Pressure

FS = Fixed Scroll

OS = Orbital Scroll

Figure 6

1

2

3

4

5

6

FS or Fixed 
Scroll

Tip Seal Removal

OS or Orbit
Scroll

Tip Seal
Set

SLAE03 SLAE03HP

SLAE05

SLAE05HP

Air End 
Model

3 hp

SLAE0

3 hp HP

5 hp

5 hp HP

Part No.

92510050

92510050

IP604600AV

92663060

Summary of Contents for SBS0307





















Reviews: