background image

Limited Warranty 

 

39 

Dear Valued Customer: 
 

 

The Powerhorse Product you just purchased is built with the finest material and craftsmanship.  Use this product 

properly and enjoy the benefits from its high performance.  By purchasing a Powerhorse product, you show a desire for quality 
and durability.  Like all mechanical equipment this unit requires a due amount of care.  Treat this unit like the high quality 
piece of machinery it is.  Neglect and improper handling may impair its performance.  Please thoroughly read the instructions 
and understand the operation before using your product. 
 

Limited Warranty 

 

Powerhorse shall warranty any

 

piece of equipment manufactured, or parts of equipment manufactured, to be free from defects 

in  material  or  workmanship  for  a  period  of  2  years  for  noncommercial/nonrental  use  and  a  period  of  90  days  for 
commercial/rental use from the date of purchase by user. 
 
Powerhorse  shall  warranty  any  wear  item,  including,  but  not  limited  to,  valves,  seals,  pump  diaphragms,  hoses,  and  filter 
elements to be free from defects in material or workmanship for a period of 90 days from the date of purchase by user.  This 
warranty  applies  to  the  original  purchaser  of  the  equipment  and  is  non  transferable.  Verification  of  purchase  is  the 
responsibility of the buyer. Parts will be replaced or repaired at no charge, except when the equipment has failed due to lack of 
proper  maintenance.  Any  misuse,  abuse,  alteration  or  improper  installation  or  operations  will  void  warranty.  Determining 
whether a part is to be replaced or repaired is the sole decision of Powerhorse. 

 
 
NOTE: 

Some services performed by parties other than Powerhorse may void warranty. 

 
 

This warranty covers parts only. It will not provide for replacement of complete products due to defective parts.  

Components not manufactured by Powerhorse are guaranteed by their manufacturer and can be serviced at factory-

authorized locations near you. Any costs incurred due to replacement or repair of items outside of a Powerhorse 

approved facility is the responsibility of the buyer and not covered under warranty. Powerhorse can supply you with 

the service center location in your area. 

 
This warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood, windstorm, 
acts  of  God,  applications  not  approved  by  Powerhorse  in  writing,  corrosion  caused  by  chemicals,  use  of  replacement  parts 
which  do  not  conform  to  manufacturer’s  specifications,  and  damage  caused  by  vandalism.  Additional  exclusions:  loss  of 
running time, inconvenience, loss of income, or loss of use, including any implied warranty of merchantability of fitness for a 
specific use. 
 
Warranty does not cover items subject to normal wear such as tires, receptacles or any part subject to direct physical contact 
by the public. This warranty does not cover any personal injury or damage to surrounding property caused by failure of any 
part.  
 
This warranty is in lieu of any other warranty expressed or implied and Powerhorse assumes no other responsibility or liability 
outside that expressed within this warranty. 
 
Please fill in the following information and have it on hand when you call in on a warranty claim. 
 
Customer Number: ______________________________________________________________ 
 
Date of Purchase: _______________________________________________________________ 
 
Powerhorse Serial Number: _______________________________________________________ 
 
Item Number: __________________________________________________________________ 
 

Summary of Contents for M1156









































Reviews: