PowerKiss Jig User Manual Download | Manualshive

Page: 15 / 16

background image

15

© PowerKiss 2011

www.powerkiss.com
info@powerkiss.com

• Don’t over reach; keep proper footing at all times to ensure correct
balance
• Wear safety goggles at all times, everyday glasses are not sufficient for
eye protection as lenses are not impact resistant and could shatter. Use
a face or dust mask if operation is likely to be dusty and ear defenders
during periods of operations

• Don’t wear loose clothing, neckties or jewellery or other items which may
get caught in moving parts. Wear non-slip footwear, cover or tie back long
hair and roll long sleeves above the elbow

• Never exceed 10mm depth cut in one cut

• Be sure to set plunge depth correctly, plunging through the table will
remove the centre plug that guides the jig and create a serious hazard

«
...
13
14
15
16
»

Summary of Contents for Jig

















Reviews:

No comments

Related manuals for Jig

Brand: Jabra Pages: 30

Brand: Gemtek Pages: 35

Brand: Systimax Pages: 197

Brand: Airlink101 Pages: 40

Brand: BridgeWave Pages: 84

Brand: Gemtek Systems Pages: 54

Brand: KOFIRE Pages: 10

Brand: Quantenna Pages: 9

Speed Wi-Fi 5G X01

Brand: AU Pages: 64

Brand: Kogan Pages: 16

Brand: Linksys Pages: 49

Brand: Linksys Pages: 70

Brand: Billion Pages: 130

Brand: Ubiquiti Pages: 12

UniFi XG UAP-XG

Brand: Ubiquiti Pages: 23

Brand: Ubee Pages: 34

Brand: Digi Pages: 726

Brand: Cambium Networks Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands