Powermatic 1632 Operating Instructions And Parts Manual Download

Page: 20 / 28

PARTS LIST: Base & Table Adjust Assembly (1632 Sander)

continued

No. Part No.

Description

Quantity

6293218

Flat Washer, 3/8..............................................................................................4

54 6293463

Shaft ...............................................................................................................1

6293267

Set Screw, 1/4 X 1/4........................................................................................2

6293464

Set Screw, 1/4 X 1...........................................................................................1

6293450

Hex Nut, 1/4 ....................................................................................................1

58 6293465

Wheel,

8" ........................................................................................................1

59 6293466

Handle ............................................................................................................1

6293209

Pan Head Screw, 1/4 X 1/2..............................................................................2

61 6293467

Lower

Guard ...................................................................................................1

62 6293468

Upper

Guard ...................................................................................................1

6293277

Hex Head Screw, 3/8 X 1-1/2 ..........................................................................8

6293342

Gear Washer, 3/8............................................................................................8

6293469

Air Cylinder Assembly .....................................................................................1

6293300

Hex Head Screw, 5/16 X 1 ..............................................................................2

6293289

Hex Nut, 5/16".................................................................................................2

6293470

Key (7-1/2 HP), 10 X 8 X 60 ............................................................................1

6293471

Key (5 HP) ......................................................................................................1

69 6293472

Cover ..............................................................................................................1

6293210

Flat Washer 1/4...............................................................................................2

6293457

Hex Nut, 3/8 ....................................................................................................1

72 6293473

Solenoid

Valve ................................................................................................1

6293331

Pan Head Screw, 5/32 X 1...............................................................................2

74 6293474

Filter................................................................................................................1

6293475

Pan Head Screw, 5/32 X 1-3/8.........................................................................1

76 6293476

Hookup

Box ....................................................................................................1

6293477

Screw, 3/16 X 1-3/8 .........................................................................................2

6293478

Flat Washer, 3/16............................................................................................2

6293479

Hex Nut 3/16 ...................................................................................................2

6293210

Flat Washer, 1/4..............................................................................................4

6293480

Screw Lead, 3/4 ..............................................................................................1

82 6293481

Lifting

Pipe ......................................................................................................1

Summary of Contents for 1632





























Search results

Summary of Contents for 1632

Reviews:

Related manuals for 1632

Brands by name

Popular brands

Powermatic 1632, Operating Instructions And Parts Manual

Search results

Summary of Contents for 1632

Reviews:

Related manuals for 1632

Brands by name

Popular brands