background image

 

 

5

If stock stops feeding:  If the board being planed stops feeding, disengage or turn the feed off and turn the power 
off.  Wait until the cutterhead comes to a complete stop before lowering the table to remove the board.  NEVER 
lower the table with the power on and the stock still in the machine, as a kickback can occur. 
 
Hand safety.  Keep hands outside the machine. NEVER reach under the guards to try to clear stock that stops 
feeding.  Do not clear chips and sawdust with hands; use a brush.  Do not have any part of the hands under that part 
of the board that is over the table when starting a cut; the infeed roll will engage the board and force it down against 
the table causing a pinching action. 
 
Cutterhead rotation:
  Be sure cutterhead rotates under power in a counterclockwise direction when viewed from 
the main drive motor side. 
 
Material condition:  Do not plane boards with loose knots or with nails or any foreign material on its surface.  Knife 
impact on these objects can cause the knives to be pulled out and cause them to shatter against the chipbreaker or 
pressure bar.  Twisted, warped, or wind in stock should first be jointed on one surface before attempting to plane a 
parallel surface on the planer.  Serious stock flaws cannot be removed by use of a planer alone. 
 
Machine capacity:
  Do not make any cuts requiring more power than is available on the machine.  Do not attempt 
to feed two boards side by side (multiple board surfacing) on any machine not equipped with sectionalized infeed roll 
and chipbreaker.  NOTE:  The 22" Planer is rated at 7.5 horsepower with maximum cutterhead speed of 4800 RPM.  
DO NOT equip your planer with a motor of higher horsepower or run the cutterhead in excess of 4800 RPM.  Doing 
so voids the warranty and Powermatic holds itself harmless from any injury that may result. 
 
Machine adjustments:
  Make all machine adjustments with power off except feed rate. 
 
Job completion. 
 If the operator leaves the machine area for any reason, the planer should be turned "off" and the 
cutterhead should come to a complete stop before his departure.  In addition, if the operation is complete, he should 
clean the planer and the work area.  NEVER clean the planer with power "on" and never use the hands to clear 
sawdust and debris; use a brush.  Disconnect machine from power source before cleaning. 
 
Replacement parts.  Use only Powermatic or factory authorized replacement parts and accessories; otherwise the 
warranty and guarantee is null and void. 
 
Misuse.  Do not use this Powermatic planer for other than its intended use.  If used for other purposes, Powermatic 
disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that 
use.   
 
If you are not thoroughly familiar with the operation of planers, obtain advice from your supervisor, instructor or 
other qualified person. 
 
Drugs, alcohol, medication.  Do not operate this machine while under the influence of drugs, alcohol, or any 
medication. 
 
Health hazards.   Some dust created by power sanding, sawing, grinding, drilling and other construction activities 
contains chemicals known to cause cancer, birth defects or other reproductive harm.  Some examples of these 
chemicals are: 
*  Lead from lead-based paint. 
*  Crystalline silica from bricks and cement and other masonry products. 
*  Arsenic and chromium from chemically-treated lumber. 
Your risk from these exposures varies, depending on how often you do this type of work.  To reduce your exposure 
to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as those dust 
masks that are specifically designed to filter out microscopic particles. 
 
 
 
 
 
 
 

Summary of Contents for 201









































Reviews: