background image

 

19

Parts List for PM1300 Canister Filter System 

Index No.  Part No. 

Description 

Size 

Qty 

................ 1791086 ..................Canister Assembly (includes #1 thru 24) .............................................. 1 
1 ..............  PM1900-301............Filter .................................................................................................. 1 
2 ..............  PM1900-302............Knob ................................................................M6x20........................ 4 
3 ..............  331031....................Pad.................................................................................................... 1 
4 ..............  331009....................Support .............................................................................................. 1 
5 ..............  ST049200 ...............Tapping Screw .................................................M4x8 ......................... 4 
6 ..............  331038....................Snap Ring .......................................................................................... 1 
7 ..............  1791087 ..................Plastic Collection Bag (Package of 5) .................800x1050x0.1t mm ..... 1 
8 ..............  TS-1540071 ............Hex Nut............................................................M10 ........................... 2 
9 ..............  TS-1550071 ............Flat Washer......................................................M10 ........................... 2 
10 ............  331050....................Handle ............................................................................................... 1 
11 ............  331051....................Soft Grip Handle ................................................................................. 2 
12 ............  TS-2361101 ............Lock  Washer ....................................................M10 ........................... 1 
13 ............  BR000052 ...............Rivet ................................................................5-2 ............................. 3 
14 ............  331014....................Bracket .............................................................................................. 1 
15 ............  150623....................Rubber Mount .................................................................................... 1 
16 ............  TS-1540041 ............Hex Nut............................................................M6 ............................. 8 
17 ............  331052....................Shaft .................................................................................................. 1 
18 ............  TS-1482041 ............Hex Cap Screw ................................................M6x20........................ 4 
19 ............  TS-2361061 ............Lock Washer ....................................................M6 ............................. 4 
20 ............  TS-1550041 ............Flat Washer......................................................M6 ............................. 4 
21 ............  331012....................Scraper .............................................................................................. 2 
22 ............  331017....................Plate .................................................................................................. 2 
23 ............  331015....................Plate .................................................................................................. 2 
24 ............  TS-1482021 ............Hex Cap Screw ................................................M6x12........................ 4 
................ PM1300-PLO...........Powermatic Label (not shown) ...........................5-1/2x14  Oval ............. 1 
................ PM1900-CHP ..........Canister Hardware Package (not shown) * ........................................... 1 
 
*Canister Hardware Package includes index # 2, 8, 9 and 12. 

Summary of Contents for PM1300

























Reviews: