background image

 

 

15 

www.powermaxfitness.net 

performance of the electric treadmill, therefore regular applying of lubricant is needed. We advise 
you to check the board regularly. If the board’s surface is damaged, please contact our customer 
service centre. 
We advise using lubricant between running belt and running board with following schedule: 
Lightweight user (use less than 3 hours a week) once per month; 
Heavyweight use (use more than 7 hours a week) once every half month. 
1. In order to maintain your treadmill better and extend the life of the machine, it is suggested that 
after your continued use of one hour, turn off the machine and let it rest for 10 minutes before using 
again. 
2. If the treadmill belt is too loose, there will be skid phenomenon’s while running; if it’s too tight, it 
may reduce motor performance and harden the abrasion of roller and the running belt. You can lift 
two sides of the running belt for 50-75mm when the tightness is appropriate.  

 
Running with adjusted alignment and tightness 

In order to better use the treadmill and make the treadmill functions work better, it is necessary for 
you to adjust the running belt into the best condition. 

Running Belt alignment 

 

Put electric treadmill flat on the ground. 

 

Make the electric treadmill run at a speed of about 6-8km/hour. 

 

If the running belt is closer to the left, rotate the left adjusting bolt with 1/2 turn clockwise, 
then rotate the right adjusting bolt with 1/2 turn counter-clockwise. (Picture A) 

 

If the running belt is closer to the right, rotate the right adjusting bolt with 1/2 turn clockwise, 
then rotate the left adjusting bolt with 1/2 turn counter-clockwise. (Picture B) 

 

                                    Picture A                                                                 Picture B     

Multi-wedge Belt Tension Adjusting 

When you use the treadmill for a long time, the multi-wedge belt becomes loose because of the 
abrasion, then you have to do some appropriate adjustment to facilitate the safe use. 
Judgment: the feeling of running with the occasional pause phenomenon, which indicating that the 
treadmill belt or multi-wedge belt are a little loose and further affirmation need to be made. 
Method of judging which part is loose: Remove the four screws on protective cover, make the 
treadmill run at a speed of 1 km/h, and then stand on the running belt, grip the armrests, and tread 
the treadmill belt slightly. (we advise treading the treadmill belts with the user's own weight) 

Summary of Contents for TAC-585


















Reviews: