background image

 

 

www.powermaxfitness.net 

15 

 
Check if the motor cable between the motor and lower 
controller is connected well, to make sure these 
connect well. 

E7 

No safety key 

Put the safety key on the right place. 

 

ROUTINE MAINTENANCE AND INSTRUCTIONS 

Warning:

 

Before cleaning or maintaining products, please be sure the power plug of the treadmill 

is pulled out. 

Cleaning:

 

Comprehensive cleaning will extend the using life of the electric treadmill. 

Remove dust periodically in order to keep the parts clean. Be sure to clean running belt with both 

sides of the exposed portion, which will reduce the accumulation of impurities. Make sure to wear 
clean athletic shoes to avoid carrying the dirty matters into running board and belt. Treadmill 
belts shall be cleaned by a damp cloth with soap. And please pay attention to avoid to wet the 
electrical components and running belt. 

Warning:

 Make sure power plug disconnect before moving motor cover away, clean the motor 

at least once a year. 

Running Belt Specialized Lubricant 

This electric treadmill’s running board and running belt has been lubricated in factory. Friction 

between  the  running  belt  and  running  board  has  a  great  influence  to  the  using  life  and  the 
performance of the electric treadmill, therefore regular applying of lubricant is needed. We advise 

you to check the board regularly. If the board’s surface is damaged, please contact our customer 

service centre. 

We  advise  using  lubricant  between  running  belt  and  running  board  with  following  schedule: 

Lightweight user (use less than 3 hours a week) once per month; 

Heavyweight use (use more than 7 hours a week) once every half month. 

 

In order to better safeguard your electric treadmill and extend the life of the machine, it is 
recommended that after your continued use of two hours, turn off the machine and let it rest 
for 10 minutes before using again. 

 

If the treadmill belt is too loose, there will be skid 

phenomenon’s

 while running

; if it’s too 

tight, it may reduce motor performance and harden the abrasion of roller and the running 
belt. You can lift two sides of the running belt for 50-75mm when the tightness is appropriate. 

Summary of Contents for TDM-100S


















Reviews: