background image

 

POWE30040 

EN

 

Copyright © 2017 VARO 

P a g e

 | 

13

 

www.varo.com 

 

At the same time, no claim can be made on the warranty if the damage of the device is the 
result of negligent maintenance or overload. 

 

Definitely excluded from the warranty is damage resulting from fluid permeation, excessive 
dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate 
usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not 
following the instructions given in the manual), inexpert assembly, lightning strike, 
erroneus net voltage. This list is not exhaustive. 

 

Acceptance of claims under warranty can never lead to the prolongation of the warranty 
period nor commencement of a new warranty period in case of a device replacement. 

 

Devices or parts which are replaced under the warranty  therefore remain the property of 
Varo NV. 

 

 We reserve the right to reject a claim whenever the purchase cannot be verified or when it 
is clear that the product has not been properly maintained. (Clean ventilation slots, carbon 
brushes serviced regularly, etc.). 

 

Your purchase receipt must be kept as proof of date of purchase. 

 

Your appliance must be returned undismantled to your dealer in an acceptably clean state, 
(in its original blow-moulded case if applicable to the unit), accompanied by proof of 
purchase. 

18 ENVIRONMENT 

Should  your  appliance  need  replacement  after  extended  use,  do  not  discard  it 
with the household rubbish but dispose of it in an environmentally safe way. 
Waste  produced  by  electrical  machine  items  should  not  be  handled  like  normal 
household rubbish. Please recycle where recycle facilities exist. Check with your 
Local Authority or retailer for recycling advice. 

Summary of Contents for POWE30040















Reviews: