Powerplus POWE30040 Manual Download

Page: 14 / 14

POWE30040

P a g e

www.varo.com

19 DECLARATION OF CONFORMITY

VARO N.V.

- Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,

product

mini plunge saw 500W

– 85mm

trade mark

PowerPlus

model

POWE30040

is in conformity with the essential requirements and other relevant provisions of the applicable
European Directives, based on the application of European harmonized standards. Any
unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of signature);

2014/30/EU
2006/42/EC
2011/65/EU

European harmonized standards (including, if applicable, their amendments up to the date of
signature);

EN60745-1 : 2009
EN60745-2-5 : 2010
EN60745-2-22 : 2011
EN55014-1 : 2006
EN55014-2 : 2015
EN61000-3-2 : 2014
EN61000-3-3 : 2013

Keeper of the Technical Documentation : Philippe Vankerkhove, VARO

– Vic. Van Rompuy

N.V.

The undersigned acts on behalf of the company CEO,

Hugo Cuypers
Regulatory Affairs

– Compliance Manager

23/02/17

Summary of Contents for POWE30040















Search results

Summary of Contents for POWE30040

Reviews:

Related manuals for POWE30040

Brands by name

Popular brands

Powerplus POWE30040, Manual

Search results

Summary of Contents for POWE30040

Reviews:

Related manuals for POWE30040

Brands by name

Popular brands