background image

 

POWX0561 

EN

 

Copyright © 2018 VARO 

P a g e

 | 

13

 

www.varo.com 

21 WARRANTY 

 

This product is warranted for a 36-month period effective from the date of purchase by the 
first user. 

 

This warranty covers all material or production flaws excluding : batteries, chargers, 
defective parts subject to normal wear & tear such as bearings, brushes, cables, and 
plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects 
resulting from maltreatment, accidents or alterations; nor the cost of transportation. 

 

Damage and/or defects resulting from inappropriate use also do not fall under the 
warranty provisions. 

 

We also disclaim all liability for any bodily injury resulting from inappropriate use of the 
tool. 

 

Repairs may only be carried out by an authorised customer service centre for Powerplus 
tools. 

 

You can always obtain more information at the number 00 32 3 292 92 90. 

 

Any transportation costs shall always be borne by the customer, unless agreed otherwise 
in writing. 

 

At the same time, no claim can be made on the warranty if the damage of the device is the 
result of negligent maintenance or overload. 

 

Definitely excluded from the warranty is damage resulting from fluid permeation, excessive 
dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate 
usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not 
following the instructions given in the manual), inexpert assembly, lightning strike, 
erroneus net voltage. This list is not exhaustive. 

 

Acceptance of claims under warranty can never lead to the prolongation of the warranty 
period nor commencement of a new warranty period in case of a device replacement. 

 

Devices or parts which are replaced under the warranty  therefore remain the property of 
Varo NV. 

 

 We reserve the right to reject a claim whenever the purchase cannot be verified or when it 
is clear that the product has not been properly maintained. (Clean ventilation slots, carbon 
brushes serviced regularly, etc.). 

 

Your purchase receipt must be kept as proof of date of purchase. 

 

Your appliance must be returned undismantled to your dealer in an acceptably clean state, 
(in its original blow-moulded case if applicable to the unit), accompanied by proof of 
purchase. 

22 ENVIRONMENT 

Should  your  machine  need  replacement  after  extended  use,  do  not  put  it  in  the 
domestic waste but dispose of it in an environmentally safe way. 
Waste electrical products should not be disposed of with household waste. Please 
recycle  where  facilities  exist.  Check  with  your  local  Authority  or  retailer  for 
recycling advice. 

Summary of Contents for POWX0561















Reviews: