background image

 

POWX07582 

EN

 

Copyright © 2017 VARO 

P a g e

 | 

4

 

www.varo.com 

4  SYMBOLS 

In this manual and/or on the machine the following symbols are used: 

 

Denotes risk of personal 
injury or damage to the tool. 

 

In accordance with essential 
requirements of the European 
directive(s) 

 

Read manual before use 

 

"Class II - The machine is double 
insulated; Earthing wire is 
therefore not necessary 

 

Wear eye protection 

 

Wear gloves 

 

Do not touch a turning saw blade. 

5  GENERAL SAFETY WARNINGS 

Read  all  safety  warnings  and    instructions.  Failure  to  heed  warnings  and  follow  instructions 
may  result  in electric  shock, fire  and/or  serious  injury. Keep safety warnings  and  instructions 
for  future  reference.  The  term  "power  tool"  in  the  safety  warnings  refers  to  your  mains-
operated (corded) power tool or battery-operated (cordless) power tool. 

5.1 

Working area 

 

Keep working area clean and well lit. Untidy and dark areas can lead to accidents. 

 

Do not operate power tools in potentially explosive surroundings, for example, in the 
presence of inflammable liquids, gases or dust. Power tools create sparks which may 
ignite the dust or fumes. 

 

Keep children and bystanders at a distance when operating a power tool. Distractions can 
cause you to lose control  of it. 

5.2 

Electrical safety 

 

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use 
adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce 
the risk of a lethal electric shock. 

 

Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and 
refrigerators. There is an increased risk of a lethal electric shock if your body is earthed. 

 

Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will 
increase the risk of a lethal electric shock. 

 

Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power 
tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or 
entangled cords increase the risk of a lethal electric shock. 

 

When operating a power tool outdoors, use an extension cable suitable for outdoor use. 
Using a cord suitable for outdoor use reduces the risk of a lethal electric shock. 

5.3 

Personal safety 

 

Stay alert, watch what you are doing and use common sense when operating a power 
tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or 
medication. A moment of inattention when operating a power tool  may result in serious 
personal injury. 

 

Use safety equipment. Always wear eye protection. Using safety equipment such as a 
dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed 
will reduce the risk of personal injury. 

Summary of Contents for POWX07582





















Reviews: