background image

11 

 

3-3. Audible Alarm   

Description 

Buzzer status 

Muted 

UPS status 
Bypass mode 

Beeping once every 2 minutes 

Yes 

Battery mode 

Beeping once every 4 seconds 

Fault mode 

 

 

Beeping continuously 

Warning 
Overload   

Beeping twice every second 

Yes 

Others 

Beeping once every second 

Fault 
All 

Beeping continuously 

Yes 

3-4. Single UPS Operation 

3-4-1. Turn on the UPS with utility power supply (in AC mode)   

1)    After power supply is connected correctly, set the breaker of the battery pack at “ON” position (the 

step only available for long-run model). Then set the input breaker at “ON” position. At this time 
the fan is running and the UPS enter to power on mode for initialization, several seconds later, UPS 
operates in Bypass mode and supplies power to the loads via the bypass.     

NOTE: When UPS is in Bypass mode, the output voltage will directly power from utility after you 
switch on the input breaker. In Bypass mode, the load is not protected by UPS. To protect your 
precious devices, you should turn on the UPS. Refer to next step.   

2)    Press and hold the “ON” button for 0.5s to turn on the UPS and the buzzer will beep once.     

3)  A few seconds later, the UPS will enter to AC mode. If the utility power is abnormal, the UPS will 

operate in Battery mode without interruption. 

NOTE: When the UPS is running out battery, it will shut down automatically at Battery mode. When the 
utility power is restored, the UPS will auto restart in AC mode.   

3-4-2. Turn on the UPS without utility power supply (in Battery mode) 

1)    Make sure that the breaker of the battery pack is at “ON” position (only for long-run model).   

2)    Press the “ON” button to set up the power supply for the UPS, UPS will enter to power on mode. 

After initialization UPS will enter to No Output mode, then Press and hold the “ON” button for 0.5s 
to turn on the UPS, and the buzzer will beep once. 

3)    A few seconds later, the UPS will be turned on and enter to Battery mode. 

3-4-3. Connect devices to UPS 

After the UPS is turned on, you can connect devices to the UPS. 

1)    Turn on the UPS first and then switch on the devices one by one, the LCD panel will display total 

load level.   

2)    If it is necessary to connect the inductive loads such as a printer, the in-rush current should be 

calculated carefully to see if it meets the capacity of the UPS, because the power consumption of 
this kind of loads is too big. 

3)    If the UPS is overload, the buzzer will beep twice every second. 

4)    When the UPS is overload, please remove some loads immediately. It is recommended to have the 

total loads connected to the UPS less than 80% of its nominal power capacity to prevent overload 

Summary of Contents for Centurion RT 6000VA
































Reviews: