background image

SPECIFIC SAFETY RULES FOR AIR FILTRATION SYSTEM

2

Be aware of general power tool safety. Make sure all the 
safety rules are understood.
•  Disconnect the machine from power source whenever 

adjusting or replacing any parts.

•  Do not plug air filtration system in unless switch is in the 

“OFF” position.

•  Keep hands away from all moving parts.
•  Wear eye protection or face shield during operation.
•  Make sure all mobile parts move freely and are free 

from interference.

•  If ceiling mounted, bottom of air filtration system must 

be at least 7 feet above the floor.

•  If ceiling mounted, mounts must be anchored to building 

structure which will support a minimum of at least 
100 pounds. Never mount to surfaces such as dry wall 
or false ceiling grinds, etc.

ASSEMBLY

UNPACKING

Refer to Figure 1

The air filtration system is shipped assembled and 
requires minimum assembly and installation.
•  Examine shipping carton for freight damage before 

opening. If shipping carton is damaged file a claim with 
the carrier immediately.

•  Carefully remove all contents from shipping carton. The 

shipping carton contains:

  1 - Air Filtration System
  1 - Remote Control  

     (Batteries Required: Two AA  batteries, Not included)

  4 - Mounting Hooks
  4 - Eye Bolts
  4 - Flange Nuts
  4 - Hook Chains
  1 - Owner's Manual (not shown)

NOTE:

 Contact the customer service center if any of these 

parts are missing. 

NOTE: 

After unit is assembled dispose of all packaging 

material in an environmentally safe way.

Air Filtration System

Carry Handle

Remote Control

Mounting Hooks (4)

Eye Bolts (4)

Flange Nuts (4)

Hook Chains (4)

Figure 1

2

ASSEMBLY

2

SPECIFIC SAFETY RULES

2

•  To reduce the risk of electrical shock, do not expose air 

filtration to water or rain. 

•  Never duct a machine directly into the air filtration 

system.

•  Do not use air filtration system without filters in place.
•  To avoid a potentially dangerous situation, do not 

use this machine to filter flammable vapors or smoke. 
This air filtration system is designed and intended 
for the filtration of airborne wood dust only. It is 
neither designed nor intended for any other purpose 
whatsoever.

•  Use the machine for filtering wood dust only. Not for 

use filtering sheet rock dust, silica, lead paint dust, 
asbestos, biohazards, smoke, toxic fumes, spray paint 
or flammable liquids.

•  Failure to follow these rules may result in serious 

personal injury/or property damage. 

Summary of Contents for AF4001















Reviews: