background image

3

ASSEMBLY

ASSEMBLY

3

ASSEMBLE EXTENSION BAR/ROLLER BAR 

LOCKING KNOBS

Refer to Figure 4, 5

The two extension bars can be assembled in the 
extension bar brackets found at the right and left of the 
stand. 

Figure 4

Extension 

Bar Bracket

Extension 

Bar Bracket

Extension 

Bar

Locking Knob

Pan Head Screw

•  Slide the extension bar into the extension bar bracket. 

Insert the pan head screw into the hole in the end of 
extention bar.   

•  Slide the extension bar in or out to desired location and 

secure in place with locking knob.

•  Place the roller arm into the roller bar support, slide up 

and down to desired location and secure in place with 
large locking knobs.

Figure 5

Roller Bar Support

Locking Knob

Roller Bar

MOUNTING THE POWER TOOL

     WARNING

Risk of accidental starting and serious personal injury. 
Unplug the power tool before attaching it to the ultra-work 
stand. 

     WARNING

Risk of serious personal injury. Always make sure the 
power tool is fully supported and securely attached to 
a level work surface. Make sure the ultra-work stand is 
located on a flat surface.

IMPORTANT: 

Use the mounting hardware supplied to 

mount the power tool to the ultra-work stand. Always 
insert the bolt from the bottom of the ultra-work stand.  
Secure at all four feet of the power tool.
•  Place the tool to be used on the table top.
•  Move the tool around until the hole pattern matches 

the slot combination on the table top, secure with the 
mounting hardware supplied. 

•  Insert the bolt through the bottom of the table and 

secure with flat washer, lock washer and nut. 

Figure 6

Bolt

Lock Washer

Nut

Flat Washer

Summary of Contents for UT1004













Reviews: