background image

GARAGE DOOR OPENERS USER MANUAL

2

1. Warnings

INHOUD

1.  

Waarschuwingen

2. Product 

omschrijving

     2.1 

toepassingen

     2.2 

Beschrijving van de automatisering

3.

Installatie

     3.1 

Inventaris van een garagedeuropener

     3.2 

Rail montage

     3.3 

Bevestig de rail aan de motor

     3.4 

Bevestig de rail op de headerwand en het plafond

     3.5 

Sluit de ontgrendelingssectie aan op de garagedeur

     3.6 

Laatste stappen voor systeem leren

     3.7 Introduction of the emergency release
4. Connection
     4.1 Accessories connection
     4.2 Door position for start-up phase
     4.3 Transmitter memorizing and erasing process
     4.4 System learning, reset process, and led display
     4.5 Programmable function indication led
     4.6 How to set the parameter
4.7 Programmable function setting
5. Function of external accessories
     5.1 Function of photocells
     5.2 Function of external push button
6. Specification

2
3
3
3
4
4
5
6
6
7
8
8
9
9
9
9

10
10
10
11
12
12
12
12

WARNING :

Please read this instruction manual carefully before theinstallation.
This manual is exclusively for qualified installationpersonnel. Powertech Automation Inc. is not responsible
forimproper installation and failure to comply with localelectrical and building regulations.
Keep all the components of PG Series garage opener system and thismanual for further consultation.

In this manual, please pay extra attention to the contentsmarked by the symbol:

Be aware of the hazards that may exist in the proceduresof installation and operation of the garage opener system.

Besides, the installation must be carried out inconformity with local standards and regulations.

If the system is correctly installed and used following allthe standards and regulations, it will ensure a high degree

of safety.

Make sure that the door works properly before installingthe garage opener system and confirm the doors are

appropriate for the application.

Do not let children operate or play with the garage opener system.

Do not cross the path of the garage opener system whenoperating.

Please keep all the control devices and any other pulsegenerator away from children to avoid the system being

activated accidentally.

Do not make any modifications to any components except that it is mentioned in this manual.

Do not try to manually open or close the doors before yourelease the opener.

If there is a failure that cannot be solved and is notmentioned in this manual, please contact qualifiedi nstallation

personnel.

Do not use the garage opener system before all theprocedures and instructions have been carried out and

thoroughly read.

Install warning signs (if necessary) on the both sides ofthe door to warn the people in the area of potentialhazards.

Summary of Contents for PG 100













Reviews: