background image

12

13

The system is a unique leading edge certification management 

system which is ideal for managing a single asset or large equipment port-
folio across multiple sites. Designed by the Lifting Solutions Group, to deliver 
optimum asset integrity, quality assurance and traceability, the system also 
improves safety and risk management levels.

Marking

 
The POWERTEX Lever Hoist is equipped with a RFID (Radio-Frequency 

IDentification) tag, which is a small electronic device, that consist of a small 

chip and an antenna. It provides a unique identifier for the block.

The POWERTEX Lever Hoist is 

CE

 marked

Standard: EN 13157

Warning tag

The warning tag shows some specific and important situations, in which you 

must pay special attention, when using POWERTEX Chain Blocks and Lever 
Hoists.

User Manuals

 

You can always find the valid and updated User Manuals on the web.

 

The manual is updated continuously and valid only in the latest version.  

NB! 

The English version is the Original instruction. 

The manual is available as a download under the following link:
www.powertex-products.com/manuals

!

Product compliance and conformity 

SCM Citra OY
Juvan Teollisuuskatui 25 C
02920 Espoo
Finland
www.powertex-products.com

Summary of Contents for 16.20PALHS10025030















Reviews: