background image

 

P2

 

POWERTRONIX Corporation 

Page 

4

 of 

10

 

 

 

 

WARNING: 

 

In an emergency, main electric supply to the unit may cut off by unplugging the power 
cord A] Either from the wall outlet or from the appliance coupler of the units supplied 
with an appliance coupler and B] from the wall outlet only for the units supplied with a 
non-detachable power cord. Some models are offered with an on/off switch.  If you 
are using one of these unites, turn the power switch OFF. 

WARNING: 

 

Do not expose to temperatures below 0° Celsius (32°F) or above 65° Celsius (149°F). 
Do not expose this apparatus to relative humidity more than 95% RH (non-
condensing). 
Do not expose to pressure levels below 68.6 kPa or above 101.3 kPa.

 

WARNING: 

 

 
This apparatus is a Class 1 equipment. 

WARNING:   

 

 
Do not modify Isolation Station unit at any time during its entire service life. If the 
Isolation Station unit is modified by any manner for any purpose during its service life, 
user needs to carry out an evaluation to the requirements of the IEC 60601-1 
standard and relevant safety standards for the end application. 
 

WARNING:   

 

 
This unit is a multiple socket outlet [MSO] device. When user connects load 
equipment to Isolation Station (MSO) the total system becomes a new ME System 
and user needs to carry out an evaluation to the requirements of IEC 60601-1 
standard for the total system. 
 

 

POWER CORD REQUIREMENTS

        

  

 

Input

: All power cords must be appropriately approved by testing agencies in the country where the 

Isolation Station 

is Used, such as UL/CSA/VDE/SEMKO, etc. For the US and Canadian market, a 

HOSPITAL GRADE plug is required for medical applications. 
 
One end (plug) must be appropriate for the wall receptacle, while the other end is made to fit into the 
power inlet of the 

Isolation Station

, this end must be of appliance type, IEC-320 female plug. All power 

cords must have grounding. 
 
 

POWER

 

AWG (NOMINAL CROSS-

SECTIONAL AREA mm

2

Cu)

RECOMMENDED LENGTH

 

300VA

 

AWG 18 (0.75mm

2

Less Than 12 Feet

 

600VA

 

AWG 18 (0.75mm

2

Less Than 12 Feet

 

800VA

 

AWG 16 (1.25mm

2

Less Than 12 Feet

 

1000VA

 

AWG 16 (1.25mm

2

Less Than 12 Feet

 

1150VA

 

AWG 14 (2.0mm

2

Less Than 12 Feet

 

1500VA

 

AWG 14 (2.0mm

2

)

Less Than 12 Feet

 

1800VA

 

AWG 14 (2.0mm

2

)

Less Than 12 Feet

 

2400VA 

AWG 12 (3.0mm

2

)

Less Than 12 Feet 

3000VA 

AWG 10 (5.0mm

2

)

Less Than 12 Feet 

 

Summary of Contents for Isolation Station Series











Reviews: