PowerVent 43VP40E2 Use And Care Manual Download

Page: 15 / 40

NOTICE: All pipe, fittings, solvent cement, primers and procedures must conform to American

National Standards Institute and American Society for Testing and Materials (ANSI/ASTM) standards.

Vertical Vent Installation

Once.the.vent.terminal.location.has.been.

determined,.make.a.hole.through.the.roof.

and.interior.ceiling.to.accommodate.the.

vent.pipe ..
Complete.the.vent.pipe.installation.to.the.

water.heater's.vent.connector.fitting.on.the.

blower.outlet ..
Support.vertical.or.horizontal.lengths.as.

previously.mentioned .
Install.adequate.flashing.where.the.vent.

pipe.passes.through.the.roof ..

Determine.the.vent.terminal.height.and.cut.

vent.pipe.accordingly ..Refer.to.the.above.

section.for.proper.vent.terminal.height ..
Connect.vent.elbow.onto.vertical.pipe.

through.roof .
Connect.short.piece.of.vent.pipe.

(approximately.3".long).to.elbow,.then.

insert.1/2".mesh.metal.screen.into.terminal.

elbow.and.join.it.to.the.short.piece.of.vent.

pipe .

Vertical Vent Termination Location

The.location.of.the.vent.terminal.depends.on.the.following.

minimum.clearances.and.considerations.(see.illustration):

..Minimum..twelve.(12).inches.above.roof .
..Minimum.twelve.(12).inches.above.anticipated.snow.level .
..Maximum.twenty-four.(24).inches.above.roof.level.without.

additional.support.for.vent .

..Four.(4).feet.from.any.gable,.dormer.or.other.roof.structure.

with.building.interior.access.(i .e .,.vent,.window,.etc .) .

..Ten.(10).feet.from.any.forced.air.inlet.to.the.building ...Any.

fresh.or.make-up.air.inlet.such.as.a.dryer.or.furnace.area.is.

considered.to.be.a.forced.air.inlet .

Short.Piece.of.Vent.Pipe

Min ..12".Above.Roof.

Min ..12".Above.

Anticipated.Snow.

Level .
Max ..24".Above.Roof.

(Without.Additional.

Support)

Insert.1/2".Mesh.Protective.

Screen.Inside.Terminal.Elbow

Vent.Pipe

Through..Roof

Elbow

Horizontal Vent Installation

Once.the.vent.terminal.location.has.been.determined,.make.a.

hole.through.the.exterior.wall.to.accommodate.the.vent.pipe ..

Vent.pipe.must.exit.exterior.wall.horizontally.only ..
Insert.a.small.length.of.vent.pipe.through.the.wall.and.connect.

the.coupling.as.shown.to.the.left ..
Place.the.1/2".mesh.metal.screen.inside.the.terminal.fitting.

and.connect.it.as.shown.to.the.vent.pipe.on.the.exterior.of.the.

building .
Complete.the.rest.of.the.vent.pipe.installation.to.the.water.

heater's.vent.connector.fitting.on.the.blower.outlet ..
If.necessary.support.horizontal.run.as.previously.mentioned .

2'.x.2'.Sheet.

Metal.Shieldon.

Brick.or.Masonry.

Walls

Outside.of

Building.Wall

From

Water.Heater

Vent.Pipe

Pipe.Coupling..

.Vent.Terminal.

with.

".Mesh.

Protective..Screen.

Inside

Vent.Terminal

Summary of Contents for 43VP40E2









































Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands

PowerVent 43VP40E2, Use And Care Manual

Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands