PowerVent 43VP40E2 Use And Care Manual Download

Page: 19 / 40

For.increased.energy.efficiency,.some.

water.heaters.have.been.supplied.with.

two.24”.sections.of.pipe.insulation ..

Please.install.the.insulation,.according.

to.the.illustrations.above,.that.best.meets.

your.requirements .

Hot and Cold Pipe Insulation Installation

Insulation Blankets

Insulation.blankets,.available.to.the.

general.public,.for.external.use.on.gas.

water.heaters.are.not.necessary ...The.

purpose.of.an.insulation.blanket.is.to.

reduce.the.standby.heat.loss.encountered.

with.storage.tank.heaters ...This.water.

heater.meets.or.exceeds.the.National.

Appliance.Energy.Conservation.Act.

standards.with.respect.to.insulation.and.

standby.loss.requirements.making.an.

insulation.blanket.unnecessary ..
The.manufacturer’s.warranty.does.not.

cover.any.damage.or.defect.caused.by.

installation,.attachment.or.use.of..

any.type.of.energy.saving.or.other.

unapproved.devices.(other.than.those.

authorized.by.the.manufacturer).into,.onto.

or.in.conjunction.with.the.water.heater ..

The.use.of.unauthorized.energy.saving.

devices.may.shorten.the.life.of.the.water.

heater.and.may.endanger.life.and.property .
The.manufacturer.disclaims.any.

responsibility.for.such.loss.or.injury.

resulting.from.the.use.of.such.

unauthorized.devices .

CAUTION: If local codes require the

application of an external insulation

blanket to this water heater, pay careful

attention to the following so as not to

restrict the proper function and

operation of the water heater:

●

..Do.not.cover.the.operating.or.warning.

labels.attached.to.the.water.heater.or.

attempt.to.relocate.them.on.the.exterior.

of.insulation.blanket .



..Do.not.apply.insulation.to.the.top.of.the.

water.heater ..This.will.interfere.with.the.

safe.operation.of.the.blower.assembly .



..Do.not.cover.the.burner.access.door,.

jacket.door,.gas.control.(thermostat)/gas.

valve.or.pressure.and.temperature.relief.

valve .



..Do.not.apply.insulation.to.the.bottom.

of.the.water.heater.or.the.area.where.

the.combustion.air.inlet.openings.and.

Flammable.Vapor.Sensor.are.located ..

This.area.must.be.unobstructed.so.as.

not.to.restrict.combustion.air.flow.to.

the.burner.or.operation.of.the.sensor .



..Inspect.the.insulation.blanket.frequently.

making.certain.it.has.not.sagged.

and.it.is.not.restricting.the.air.flow.

to.the.combustion.air.inlet.openings.

(perforation.holes).or.the.Flammable.

Vapor.sensor.located.around.the.lower.

perimeter.of.the.water.heater.jacket ..

This.could.result.in.an.unsafe.operating.

condition .

WARNING: If local

codes require external

application of insulation

blanket kits the

manufacturer’s instructions

included with the kit must

be carefully followed.

NOTICE: If pipe

insulation is used, ensure

that the thickness does

not exceed ½”. Insulation

thicker than ½” can

interfere with the Blower

Assembly Dilution Air

Holes.

Dilution Air

Intake

Typical vertical piping arrangement

Typical horizontal piping arrangement

Summary of Contents for 43VP40E2









































Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands

PowerVent 43VP40E2, Use And Care Manual

Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands