PowerVent 43VP40E2 Use And Care Manual Download

Page: 30 / 40

Operating the water heater cont.

The.following.is.additional.information.which.aid.in.deter-

mining.a.safe.working.temperature.to.meet.each.household.

need .

Maximum.water.temperatures.occur.just.after.the.burner.

has.shut.off ...To.determine.the.water.temperature,.turn.on.

a.hot.water.faucet.and.place.a.thermometer.in.the.water.

stream ...If.an.adjustment.to.the.water.temperature.is.pre-

ferred,.then.refer.to.the.Water.Heater.User.Display.–.Opera-

tion.Instructions.for.instruction.on.adjusting.the.local.and.

remote.user.display.temperature.setpoints .

A.condition.known.as.“stacking”.or.“layering”.can.occur.

when.a.series.of.short.and.frequent.hot.water.draws.are.

taken ...The.hottest.temperature.water.will.be.at.the.top.of.

the.tank,.closest.to.the.outlet.pipe.delivering.hot.water.to.

the.home .

Stacking.can.cause.this.top.layer.of.water.to.be.hatter.than.

the.water.toward.the.bottom.of.the.tank.near.the.gas.control.

(thermostat) ....Therefore,.always.remember.to.test.the.water.

temperature.with.your.hand.before.use.and.remember.that.

hotter.water.increases.the.risk.of.scald.injury ..

Also,.always.supervise.young.children.or.others.who.are.

incapacitated .

The.gas.control.(thermostat).is.constructed.with.a.built.in.

safety.shut-off.device.designed.to.shut.off.the.gas.supply.to.

the.burner.if.the.main.burner.is.extinguished.for.any.reason .

The.gas.control.(thermostat).is.also.equipped.with.a.gas.

shut.off.device.that.will.shut.off.the.gas.supply.to.the.burn-

er.if.the.water.heater.exceeds.normal.operating.tempera-

tures ...Refer.to.the.“Before.You.Call.For.Service”.section.of.
this.manual,.or.contact.your.dealer .

WARNING: Should overheating occur or

the gas supply fail to shut off, turn off the

manual gas control valve to the appliance

If.the.water.heater.has.been.subjected.to.fire,.flood.or.physi-

cal.damage,.turn.off.the.manual.gas.control.(shut-off).valve.

and.do.not.operate.the.water.heater.again.until.it.has.been.

checked.by.a.qualified.service.technician .

NOTICE:..Replace.any.part.of.the.gas.control.system.

which.has.been.under.water .

Time/Temperature Relationship in Scalds

...Water.Temperature.

Time.To.Produce.a.Serious.Burn

120°F

More than 5 minutes

125°F

to 2 minutes

130°F

About 30 seconds

135°F

About 10 seconds

140°F

Less than 5 seconds

145°F

Less than 3 seconds

150°F

About 1

seconds

155°F

About 1 second

Table.courtesy.of.Shriners.Burn.Institute

90° F

113°F

98°F

105°F

120°F

130°F

140°F

150°F

160°F

Temperatures are approximate

Water Temperature Setting…

Summary of Contents for 43VP40E2









































Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands

PowerVent 43VP40E2, Use And Care Manual

Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands