PowerVent 43VP40E2 Use And Care Manual Download

Page: 32 / 40

Care and cleaning of the water heater.

Draining the Water Heater

CAUTION: Shut off gas to the water

heater at the

gas control

(thermostat) gas

cock or manual shut-off valve before

draining water.

DANGER: Before manually operating the

temperature and pressure relief valve, make

certain no one will be exposed to the hot

water released by the valve. The water

drained from the tank may be hot enough to

present a scald hazard and should be

directed to a suitable drain to prevent injury

or damage.

Before.turning.off.the.cold.water.supply.to.

the.water.heater,.open.a.hot.water.faucet.

allowing.sufficient.cold.water.into.the.

tank.to.prevent.the.risk.of.a.scald.injury.

while.draining.the.water.heater ...Once.the.

water.in.the.tank.is.no.longer.hot,.turn.off.

the.cold.water.supply.to.the.water.heater ...

Open.a.hot.water.faucet.or.lift.the.handle.

on.the.relief.valve.to.admit.air.to.the.tank ..
Attach.a.garden.hose.to.the.drain..

valve.on.the.water.heater.and.direct..

the.stream.of.water.to.a.drain ..Open..

the.valve .

Routine Preventative Maintenance

Properly.maintained,.your.water.heater.

will.provide.years.of.dependable.trouble-

free.service ..
It.is.recommended.that.a.periodic.

inspection.of.the.gas.control.(thermostat),.

burner,.relief.valve,.internal.flue-way.and.

venting.system.should.be.made.by.service.

personnel.qualified.in.gas.appliance.repair .
It.is.suggested.that.a.routine.preventative.

maintenance.program.be.established.and.

followed.by.the.user .
Inspect.plastic.vent.pipe ...Make.certain.

that.all.joints.are.secure.and.that.vent.

pipe.supports.are.all.in.place ...Check.

the.outdoor.vent.terminal.to.see.that.it.is.

free.of.obstructions,.and.that.there.is.no.

damage.nearby.casused.by.condensate .
Inspect.dilution.air.inlet.and.combustion.

air.inlet.openings ...Make.certain.no.

blockage.exists ...Clean.any.lint,.dirt.or.oil.

accumulation.that.may.exist .
At.least.once.a.year,.lift.and.release.the.

lever.handle.on.the.temperature.pressure.

relief.valve,.located.near.the.top.of.the.

water.heater,.to.make.certain.the.valve.

operates.freely ..Allow.several.gallons.to.

flush.through.the.discharge.line.to.an.open.

drain .
NOTICE:.If.the.temperature.and.pressure.

relief.valve.on.the.water.heater.discharges.

periodically,.this.may.be.due.to.thermal.

expansion.in.a.closed.water.system ..

Contact.the.water.supplier.or.your.

plumbing.contractor.on.how.to.correct.this .

DO NOT

.plug.the.relief.valve.outlet .

A.water.heater’s.tank.can.act.as.a.settling.

basin.for.solids.suspended.in.the.water ..

It.is.therefore.not.uncommon.for.hard.

water.deposits.to.accumulate.in.the.bottom.

of.the.tank ...If.allowed.to.accumulate,.

these.solids.can.cover.the.gas.control.

(thermostat).sensors,.causing.the.sensors.to.

operate.erratically ...Because.accumulated.

solids.can.prevent.the.gas.control.

(thermostat).sensors.from.accurately.

reading.the.water.temperature,.the.water..

at.the.fixture.can.be.hotter.than.the.gas.

control.(thermostat).setting ...It.is.suggested.

that.a.few.quarts.of.water.be.drained.from.

the.water.heater’s.tank.every.month.to.

clean.the.tank.of.these.deposits ..
Rapid.closing.of.faucets.or.solenoid.valves.

in.automatic.water.using.appliances.can.

cause.a.banging.noise.heard.in.a.water.

pipe ..Strategically.located.risers.in.the.

water.pipe.system.or.water.hammer.

arresting.devices.can.be.used.to.minimize.

the.problem .
The.anode.rod.should.be.removed.from.the.

water.heater’s.tank.annually.for.inspection.

and.replaced.when.more.than.6”.of.core.

wire.is.exposed.at.either.end.of.the.rod .
Make.sure.the.cold.water.supply.is.turned.

off.before.removing.anode.rod .
This.water.heater.incorporates.a.

combustion.shut.off.device.that.shuts.

the.operation.of.the.water.heater.down.if.

undesirable.combustion.conditions.occur,.

such.as.the.presence.of.flammable.vapors.

or.blockage.of.the.combustion.air.inlet.

openings ...Please.contact.a.qualified.

Service.Technician.if.this.occurs .

DANGER: Failure to perform the

recommended Routine Preventative

Maintenance can harm the proper

operation of this water heater, which

can cause carbon monoxide dangers,

excessive hot water temperatures and

other potentially hazardous conditions.

DANGER: Before

manually operating the

relief valve, make certain

no one will be exposed to

the danger of the hot water

released by the valve. The

water may be hot enough to

create a scald hazard. The

water should be released

into a suitable drain to

prevent injury or property

damage.

DANGER: Hotter water

increases the potential for

Hot Water Scalds.

Dilution Air Inlet

Tall Models

Blower Assembly Dilution Air Holes

Short.Models

Summary of Contents for 43VP40E2









































Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands

PowerVent 43VP40E2, Use And Care Manual

Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands