PowerVent 43VP40E2 Use And Care Manual Download

Page: 33 / 40

Housekeeping

Visually.inspect.the.pilot .
To.ensure.sufficient.ventilation.and.

combustion.air.supply,.proper.clearances.

must.be.maintained ..

When.installed.in.a.closet,.DO.NOT.block.

or.obstruct.any.of.the.combustion.air.inlet.

openings.located.around.the.perimeter.of.the.

water.heater ....A.minimum.of.1”.is.required.

between.these.combustion.air.inlet.openings.

and.any.obstruction .

DO.NOT.obstruct.or.block.the.Flammable.

Vapor.Sensor ...The.sensor.does.not.

require.any.maintenance.or.cleaning ...DO.

NOT.expose.to.cleaning.agents .

DANGER: Combustible

materials, such as clothing,

cleaning materials, or

flammable liquids, etc., must

not be placed against or next

to the water heater.

Burner Inspection

Visually.inspect.the.pilot.flame.and.main.

burner.annually .
Through.the.sight.glass,.inspect.the.pilot.

and.burner.lighting ...If.any.unusual.pilot.

or.burner.operation.is.noted,.the.water.

heater.should.be.shut.off.until.qualified.

service.assistance.can.be.obtained .

CAUTION: For your safety, cleaning of

the burner must be performed only by

qualified service personnel, as it involves the

disconnection of gas piping and leak testing.

The burner chamber is a sealed area. If the

burner access door is removed, the burner

access door gasket must be replaced.

For.cleaning,.remove.the.burner.from.the.

water.heater ..A.vacuum.cleaner.can.be.

used.on.the.burner.and.floor.shield.inside.

the.water.heater ...The.burner.can.also.be.

cleaned.by.scrubbing.with.mild.detergent .

Proper.burner.flame.pattern

Venting System Inspection

The.water.heater’s.internal.flue.must.be.

inspected.annually.to.be.certain.it.is.clean.

by.removing.the.blower.assembly.and.flue.

baffle .
When.reinstalling.the.flue.baffle.make.

certain.it.is.hung.securely.by.its.hanger.at.

the.top.of.the.flue.way .
Reinstall.the.blower.assembly .
Inspect.plastic.vent.pipe ...Make.certain.

that.all.joints.are.secure.and.that.vent.

pipe.supports.are.all.in.place ...Check.

the.outdoor.vent.terminal.to.see.that.it.is.

free.of.obstructions,.and.that.there.is.no.

damage.nearby.caused.by.condensate .

Inspect.dilution.air.holes ...Make.certain.no.

blockage.exists ...Clean.any.lint,.dirt.or.oil.

accumulation.that.may.exist .
Test.for.spillage.at.the.dilution.air.holes.

after.5.minutes.of.burner.operation ...Place.

a.blown.out.match.or.candle.close.to.the.

dilution.are.holes ...The.smoke.from.the.

candle.or.match.should.be.drawn.into.the.

dilution.air.holes ...If.the.smoke.is.pushed.

away.from.the.dilution.air.holes,.the.

blower.or.vent.system.may.be.blocked ...

Contact.qualified.service.personnel .

Dilution Air Inlet

Tall Models

Blower Assembly Dilution Air Holes

Short.Models.

Summary of Contents for 43VP40E2









































Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands

PowerVent 43VP40E2, Use And Care Manual

Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands