background image

EN 

 

EN

EN 

1. INTRODUCTION 

 

1.1 General Introduction 

This  series  UPS  is  pure  sine  wave  line  interactive  uninterruptible  power 
system  with  compact  design,  and  it  is  designed  for  critical  application  and 
environment, such as desktops, servers, workstations, and other networking 
equipments.  The  capacity  range  is  available for  1000VA,  and  1500VA.  This 
series protects your sensitive electronic equipments against power problems 
including power sags, spike, brownouts, line noise, and blackouts. 
 
This series is powered from the AC mains and supply also AC power backup. 
Communication  and  control  to  the  unit  is  available  through  serial  or  USB 
ports located on the rear panel. The serial port will support communications 
directly with a server. The communications protocol for the serial ports shall 
conform to true RS232 interface. 
 

This series is designed with outstanding performance and reliability. The 
unique features include the following: 
 

 

Microprocessor control guarantees high reliability 

 

High frequency design 

 

Built-in boost and buck AVR   

 

User replaceable design for 1000VA /1500VA models 

 

Selectable output range and line sensitive 

 

Cold startup capability 

 

Built-in Dry contact/RS-232/USB communication port 

 

Overload, Short-circuit, and overheat protection 

 

Rack/Tower 2 in 1 Design for 1000VA/1500VA models 

 

Network  Transient  Protector  guards  your  network  communications 

equipment from surges.

 

 

 

 

 

Summary of Contents for VI 1000RT/LE
























Reviews: