background image

 
 

 

EN 

 

 

The  internal  short  circuiting  of  the  UPS  will  lead  to  dangers  such  as 

electric shock or fire; therefore do not allow liquids or any foreign object to 

enter the UPS. No water containers (such as a water glass) or any other 

liquid-containing vessels shall be placed on the top of the UPS so as to 

avoid such dangers as electric shock. 

 

Please do not use the UPS in excess of the rated load capacity. 

 

Unplug the UPS prior to cleaning and do not use liquid or spray detergent. 

 

Risk  of  electric  shock,  do  not  attempt  to  disassemble  the  unit.  No  user 

serviceable parts inside. Refer servicing to qualified service personnel. 

 

If UPS is to be stored for a long time, it is recommended to recharge the 
batteries  (by  connecting  the  utility  power  to  UPS,  switch  “ON”),  once  a 
month for 24 hours to avoid a full battery discharge. 

 

In  case  smoke  is  found  coming  out  from  the  device,  please  cut  off  the 

power supply quickly and contact the distributor. 

 

The UPS contains one/two large-capacity batteries. So the shell shall not 

be  opened,  otherwise  such  dangers  as  electric  shock  will  be  caused.  If 

any  internal  overhaul  or  replacement  of  the  battery  is  required,  please 

contact the distributor. 

 

Servicing  of  batteries  should  be  performed  or  supervised  by  personnel 

knowledgeable  of  batteries  and  the  required  precautions.    Keep 

unauthorized personnel away from batteries. 

 

A  battery  can  present  a  risk  of  electrical  shock  and  high  short  circuit 

current. The following precautions should be observed when working on 

batteries: 

o

  Remove watches, rings, or other metal objects from the hand. 

o

  Use tools with insulated handles and wear rubber gloves and boots. 

o

  Do not lay tools or metal parts on top of batteries. 

o

  Disconnect  charging  source  prior  connecting  or  disconnecting 

batteries terminals. 

 

When replacing batteries, replace with the same type and number of the 

sealed lead-acid batteries. 

 

The maximum ambient temperature rating is 40°C. 

Summary of Contents for VI 1000T/HID





















Reviews: