background image

15 

 

Symptom

 

Possible cause

 

Remedy

 

Fault code is shown as 14 on 
LCD display and alarm is 

continuously sounding. 

The UPS shut down 

automatically because short 

circuit occurs on the UPS 

output. 

Check output wiring and  if 

connected devices are in 

short circuit status. 

Fault code is shown as 01, 02, 03,  A  UPS  internal  fault   has  Contact your dealer 

11, 12, 13 and 41 on LCD display  occurred.  There  are   two 
and alarm is continuously 

possible results: 

sounding. 

1. The load is still supplied, 

but directly from AC power 
via bypass. 
2.  The  load  is  no longer 

supplied by power. 

Battery backup time is shorter 
than nominal value. 

Batteries are not fully 
charged 

Charge the batteries for at 
least 5 hours and then 
check capacity. If the 

problem still persists, 
consult your dealer. 

Batteries defect 

Contact your dealer to 

replace the battery. 

Fault code is shown as 45 on LCD 
display. At the same time, alarm is 
continuously sounding. 

The charger does not have 
output and battery voltage 
is less than 10V/PC. 

Contact your dealer. 

 
 

 

5. Storage and Maintenance 

Operation  

The UPS system contains no user-serviceable parts. If the battery service life (3~5 years at 
25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case, 
please contact your dealer.  

 
 

 
 

Storage  

Before storing, charge the UPS 5 hours. Store the UPS covered and upright in a cool, dry 
location. During storage, recharge the battery in accordance with the following table: 

Storage Temperature 

Recharge Frequency 

Charging Duration 

-25°C - 40°C 

Every 3 months 

1-2 hours 

40°C - 45°C 

Every 2 months 

1-2 hours 

 

 

 

 

Be sure to deliver the spent battery to a recycling facility or ship it to your 

dealer in the replacement battery packing material. 

 

 

 

Summary of Contents for VI TW 1.1K



















Reviews: