- 3 -
Standards for safety must be followed in accordance with the
country laws where the equipment is being operated.
The PAS40R is designed to be simple, easy to operate, and safe.
Guidelines must be followed to ensure compliance with safety
i s s u e s .
Operators must be dressed appropriately with no loose clothing,
wide sleeves, dangling belts, ties, or other articles of clothing that
could become entangled in the machine. Shoes must also be
appropriate for the environment with no bare feet, no sandals or
open toed shoes and no wet feet.
The PAS40R is designed to work in closed industrial environments
on level floor or on inclines no steeper than 2%.
C A U T I O N :
Do not operate machine or charger in areas where
flammable liquids or gases are present.
C A U T I O N :
Do not use or pick up flammable chemicals or
liquids with this machine.
To prepare the area for cleaning, all loose objects must be picked
up prior to using the auto scrubber. Major dirt should be cleared
with an automatic sweeper or manually to avoid immediately
choking the intake circuit. This preparation will also allow the
solution to work more effectively.
Should the area require particular attention or a second pass of
the auto scrubber, it is most effective to make one pass with the
wiper raised and the brush in the working position. The solution
will remain on the floor longer and will dissolve the tougher dirt.
The second pass should be made with the brush and wiper low-
ered and at a slower speed.
CAUTION:
The charger must be switched off before
disconnecting it from the batteries.
When the area is prepared for cleaning, switch off the battery
charger and disconnect it from the PAS40R. Adjust the seat posi-
tion of the machine to suit the requirements of the operator by
using the (M16) lever. The PAS40R is ready for operation.
Operating the PA S 4 0 R
The PAS40R is designed with a safety feature that prevents opera-
tion of the machine unless an operator is seated. Once seated with
the seat adjusted to the proper position, cleaning can begin.
1. Place the (M14) lever in the, central, NEUTRAL position and
grip the (M17) steering wheel.
2. Insert the (M7) key switch to enable the electrical circuits.
3. If an acoustic BEEP signal sounds, the parking brake is
engaged and should be released with the (M19) pedal.
4. Engage brush rotation with (M12) potentiometer and the
aspirators with the (M13) switch.
5. Gradually open the solution supply tap (M18) according to
the speed of operation.
6. Engage the FORWARD or REVERSE gear with the (M14) lever
and gradually depress the (M22) accelerator pedal. When the
PAS40R is in movement, the (M28) lamp flashes. When the
REVERSE gear is engaged an acoustic BEEP signal is emitted.
I n s t r u m e n t a t i o n
M 1
Detergent intake plugs
M 2
Waste water rapid drainage tap
M 3
Waste water rapid drainage pipe
M 4
F l o o r-wiper adjustment knobs
M 5
Battery charging connector
M 6
Emergency button
M 7
Start-up key switch
M 8
Forward speed regulator (from 1 to 10)
M 9
Working hours (brushes in operation) recorder and
battery charge gauge
M 1 0
Ammeter indicating power absorption of brush motors
M 1 1
Brush rotation engagement pilot light
M 1 2
Brush ignition and regulator (from 1 to 10)
M 1 3
Aspirator start switch
M 1 4
Forward-neutral-reverse gear lever
M 1 5
H o r n
M 1 6
Seat position adjustment lever
M 1 7
Steering wheel
M 1 8
Solution supply lever
M 1 9
Parking brake
M 2 0
Parking brake locking lever
M 2 1
B r a k e
M 2 2
A c c e l e r a t o r
M 2 3
Brush engagement knob
M 2 4
Floor wiper pressure knob
M 2 5
Solution rapid drainage pipe
M 2 6
Solution rapid drainage tap
M 2 7
Motor stop ring
M 2 8
Drive engaged warning lamp
M 2 9
Exhaust gasket
M 3 0
Skirt support rod
M 3 1
Detergent filter
M 3 2
Protection fuse control panel
