background image

3

SAFETY

D a n g e r !   K e e p   c l e a r   o f 
moving parts!

Do not remove jammed logs 
with your hands.

Dispose of the used oil in an 
environment-friendly way.

Before starting any repair 
maintenance or cleaning, 
always disconnect the power.

Do not use in the rain.

Keep bystanders away from 
the working area.

W a r n i n g !   S t a y   c l e a r   o f 
moving parts!

Safety Warnings & Instructions

UNDERSTAND YOUR LOG SPLITTER

DRUGS, ALCOHOL AND MEDICATION 

AVOID DANGEROUS CONDITIONS

Read and understand the owner's 
manual and labels affixed to the log 
splitter. Learn its application and 
limitations as well as the specific 
potential hazards peculiar to it.

Do not operate the log splitter while 
under the influence of drugs, alcohol, 
or any medication that could affect 
your ability to use it properly.

Put the log splitter on a 72-85 cm high, 
stable, flat, and level work bench where 
there is plenty of room for handling, 
and help the operator stay altert. Bolt 
the log splitter to the work surface if it 
tends to slip, walk, or slide.

Keep your work area clean and well lit. 
Cluttered areas invites injuries. 

INSPECT YOUR LOG SPLITTER

Check your log splitter before turning 
i t   o n .   K e e p   g u a r d s   i n   p l a c e   a n d 
in working order. Form a habit of 
checking to see that keys and adjusting 
wrenches are removed from tool area 
before turning it on. Replace damaged, 
missing or failed parts before using it.

DRESS PROPERLY

Do not wear loose clothing, gloves, 
neckties or jewelry (rings, wrist watches). 
They can be caught in moving parts.

Protective electrically non conductive 
gloves and non-skid footwear are 
recommended when working. Wear 
protective hair covering to contain long 
hair, preventing it from get caught in 
machinery.

PROTECT YOUR EYES AND FACE

Any log splitter may throw foreign 
objects into the eyes. This can cause 
permanent eye damage. Always wear 
safety goggles. Everyday eyeglasses 
have only impact resistant lenses. They 
are not safety glasses. 

Do not put the log splitter on the ground 
for operations. This is awkward operating 
position means that the operator has to 
bring his face close to the machine, and 
thus risks being struck by wood chips or 
debris.

Do not use the log splitter in wet or 
damp areas or expose it to rain.

Do not use it in areas where fumes 
from paint, solvents or flammable 
liquids pose a potential hazard.

EXTENSION CORDS

Improper use of extension cords may 
cause inefficient operation of the log 
splitter which can result in overheating. 
Be sure the extension cord is no longer 
than 10m and its diameter is no less than 
2.5mm

 to allow sufficient current flow to 

the motor. 

Avoid use of free and inadequately 
insulated connections. Connections must 
be made with protected material suitable 
for outdoor use.

65575UK00M111.indd   3

2019/8/30   11:52:29

Summary of Contents for 65575

























Reviews: