background image

 

17 

Section IX Warranty 

The product quality shall comply with the following provisions: 
1. Warranty terms 
1-1. The product from the user the date of purchase, the warranty period 

of 12 months (limited to domestic market). 

1-2.  Export  products  and  non-standard  products  warranty  period  is  12 

months or according to the agreement of warranty execution. 

1-3.  The  product  from  the  user  the  purchase  date,  guarantee  to  return, 

replacement, repair service, within one month after the date of shipment. 

1-4. The product from the user the date of purchase, replacement, repair 

within three months after the date of shipment. 

1-5.  The  product  from  the  user  the  purchase  date,  enjoy  lifelong 

compensable service. 

 
2. Exceptions clause 
If belongs to the quality problems caused by following reasons products, 

not within the warranty. 

2-1.  The  user  is  not  in  accordance  with  the  "products  manual"  is  used 

method of operation caused the failure. 

2-2. Users without permission to repair or alteration caused by  product 

failure. 

2-3.  Users  beyond  the  standard  specifications  require  the  use  of  the 

inverter caused by product failure. 

2-4.  Users  to  buy  and  then  fell  loss  or  damage  caused  by  improper 

handling. 

2-5.  Because  the  user  use  environment  device  caused  by  aging  lead  to 

product failure. 

2-6. Due to the fault cause of earthquake, fire, lightning, wind or water 

disaster, abnormal voltage irresistible natural disasters. 

2-7.  Damaged  during  shipping  (Note:  the  transport  mode  specified  by 

the customer, the company to assist to handle cargo transfer procedures). 

 
3.  The  following  conditions,  manufacturers  have  the  right  not  to  be 

warranty 

3-1.  No  product  nameplate  or  product  nameplate  blurred  beyond 

recognition. 

3-2.  Not  according  to  the  purchase  contract  agreement  to  pay  the 

money. 

3-3. For installation, wiring, operation, maintenance and other users can 

not describe the objective reality to the company's technical service center.  

4. In return, replacement, repair service, shall be returned the company, 

confirmed the attribution of responsibility, can be returned or repair 

Summary of Contents for PB6012




















Reviews: