background image

 

Section I Safety Precautions 

Please read the manual before the installation, operation and inspection of 

the product. For the safe operation, remind  you  to  pay special  attention to the 
“Warning” and “Attention” in the manual. 

*Attention

 

The potential danger will lead to slight or medium life harm or 

equipment damage. It could also warn the violate operation.

 

 

Warning

 

The potential danger could lead to life harm or private loss! 

Statement:

  When  the  brake  unit  is  used  with  other  brand 

frequency  inverter  together,  our  company  is  only  undertake  the 
product  quality  problems  of  3  packets  of  responsibility;  If  the 
customer  need  other  projects  of  joint  liability  guarantee,  Please   
cover insurance of the related domestic property insurance company 
yourself,  In  order  to  obtain  relatively  good  liability  to  pay 
compensation. 

*Attention

 

 

*Attention

 

● 

Do  not  use  any  brake  unit  and  brake  resistor  lack  of  or  with 
damaged spares.

 

● 

Do not touch the internal spares for there are CMOS spares on the 
control  card  of  the  brake  unit.  Otherwise  it  will  damage  the 
spares. 

● 

Please  add  the  fan  or  other  cooling  equipment  when  multiple 
brake units installed parallel in the one cabinet.   

Summary of Contents for PB6012




















Reviews: