background image

21

16 - INVERTER PARAMETERS PROGRAMMING

16.1 - Operator model selection

The control board can operate, by using the same firmware, in both gates / doors and barriers.

To select the model, just remove the TST jumper and close the pines C/P (Cancel/Gate). When the function is selected the led “OSC” 

flashes  fast for a certain period of time and then indicates its value,

The following table shows the number of flashes for each function:

  

The pause between flashes is three seconds and flashes occur every half second, so they are very different.

To increase the values, just press the plus button "(+)" and to decrease just press the button less "(-)".

When you reach the desired template, return the jumper C / P to the TST position. Done that the plant is ready to operate in the chosen 

gate operator model.

16.2 - JUMPER TST

When the TST jumper is removed, the control board enters in a mode that allows to position the gate operator at a given point of its 

travel to set limits or to verify the mechanical part.

In this mode, pressing the (-) button starts the motor clockwise rotation while the button is pressed, and when the (+) button is pressed 

the motor rotates in direction counterclockwise in the same manner.

 

16.3 - Adjustment of other parameters

The control board also has other functions controlled by the DS1 DIP switch. When one selects one function, the 'OSC' LED rapidly blinks 

for a specific period of time and the indicates its parameter. When the 'OSC' LED blinks each half second (0.5s), the minimum value is 

selected; when it is off, a intermediate value is selected and when it keeps lit, the maximum value is selected. In order to increase the 

values, just press the '+' button; to decrease the values, just press the '-' button when the desired function is selected.

When leaving the function, the 'OSC' LED rapidly blinks again for a specific period of time, and then blinks in a one-second interval 

again.

Numbers of flashes

Referent Model

1

Nexus 600 / 900 / 1300 SL (SLS)

2

Nexus 2600 SL (SLS)

3

Dz Rio

4

Dz Predial / Condominium / 1500

5

Dz 2500 / 1500 HW

6

Barrier 14

Summary of Contents for DZ 1500





































Reviews: