PPA DZ HOME Technical Manual Download

Page: 3 / 18

INDEX

Important safety instructions .............................................................................3

Technical characteristics ...................................................................................4

Tools required for installation .............................................................................5

Electrical installation ..........................................................................................5

Care with the electrical installation ....................................................................6

Care with the gate before operator ...................................................................7

Installing and fixing the operator .......................................................................8

Equipment dimensions ......................................................................................8

Analog limit switch installation ...........................................................................13

Maintenance ......................................................................................................16

Summary of Contents for DZ HOME


















