Praxis Works, LLC 207 MCPHERSON ST. SUITE E. SANTA CRUZ, CA 95060 www.praxis-works.com
• Praxis Works products are warranted to be free from defects in materials or workmanship for two years after original
purchase. The warranty is non-transferable and valid to the original purchaser of the product only.
• Any attempt to modify the product in any way such as drilling, grinding or painting will void the warranty.
• This warranty is not valid for “abused” or neglected products, or products that are damaged by improper installation.
• If a defect is found, our entire liability and your sole remedy shall be, at our option, free repair or replacement of the
Praxis product.
• Except as expressly required by law, Praxis Works shall not be held liable for any indirect, special, or consequential
damages.
THIS WRITTEN EXPRESS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, IMPLIED OR EXPRESSED. This warranty
gives you specific legal rights, and you may also have other rights which vary state to state.
For more information on
warranty policy and instructions for completing a warranty claim, check out the Full Warranty Policy found at our web-
site. www.praxis-works.com
WARRANTY
Since specific tools and experience are necessary for proper installation, it is recommended that the
product be installed by a qualified bicycle technician.
Read the service instructions of your crank carefully prior to installing the parts. Loose, worn or damaged parts may
cause riding problems and serious injury may occur as a result. If installation and adjustments are not carried out cor-
rectly, the chain may come off and this may cause you to fall off the bicycle which could result in serious injury.
Read
these instructions carefully, and keep them for later use.
• Be careful not to let your clothing get caught in the chain while riding, otherwise you may fall off the bicycle.
• Check that the tension of the chain is correct and that the chain is not damaged. If the tension is too weak or the
chain is damaged, the chain should be replaced. The chain may break and you may fall off the bicycle if this is not
done.
•
Use a torque wrench to check the final tightening torque of the main crank bolt and chairing bolts. Furthermore, after
riding approximately 100 km (60 miles), use a torque wrench to re-check the tightening torques.
Main Crank bolt =
Torque 48-55Nm.
Chainring Bolts =
Torque 8-10Nm.
• If the bottom bracket shell is not parallel, shifting performance will be affected and performance will drop.
• Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the crank arm may
break and you may fall off the bicycle.
• Before riding the bicycle, check that there is no play or looseness in the bottom bracket connection. Also, be sure to
retighten the crank, chain ring bolts, and pedals at periodic intervals
• If you feel any looseness or ‘play’ in the bearings, the bottom bracket should be inspected/replaced.
• To ensure the designed performance, only use 10 or 11or 12sp chains.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a profes-
sional bicycle dealer or call Praxis Works.
• Praxis Works assumes no responsibility for damages or injury related to improperly installed components.
READ THE STEP BY STEP INSTRUCTIONS PROVIDED ON THE OTHER SIDE.
SAFETY INFORMATION - READ BEFORE RIDE
Note: specifications are subject to change without notice. © August 2017 by Praxis Works, LLC
Rev A
M24 MTB CRANK
STANDARD SPIDER
Models - M24 Girder and M24 Cadet
Required Installation Tools
M24 BSA BB
One Shimano or Sram BB Tool and 3/8” Drive Ratchet
M24 BB90/92
BB/Headset Press Tool
M24 CONVERSION BB
Two Shimano or Sram BB Tools
and 3/8” Ratchet and BB/Headset Press Tool
GREASE SPINDLE
USE TORQUE
WRENCH!
INSTALLATION
Slide the Drive side 24mm ID
Wave Washer onto the spindle.
Next slide on the
30mm ID Drive Side
dust cover
with the Praxis wordmark facing
out/away from the frame.
Now grease the spindle and insert the
crankset into the Drive cup and push spindle
through bottom bracket.
1
Slide the
22mm ID Non-Drive Side dust cover
onto the spindle, with the Praxis wordmark
side facing out/away from the frame.
2
Use an
8mm hex
torque wrench and tighten
the Non-Drive crankarm bolt to
48-55Nm.
Spin crank to make sure it moves freely.
Your installation is now complete.
3
See BB Instructions for the proper
dust cover setup for your crank
