background image

Address

 of the manufacturer 

21 

Address of the manufacturer 

Prebena 

Wilfried Bornemann GmbH & Co. 

Mounting technique 

Seestrasse 20

–26 

D-63679 Shotten 

Phone:  

 

+49 (0) 60 44 / 96 01-100 

Fax:  

 

+49 (0) 60 44 / 96 01-820 

E-Mail:  

 

info@prebena.de

 

Web-site.:  

www.prebena.de

 

Warranty 

For the described device company Prebena provides  1  year  warranty from date of sale in accordance  with 
the  following  warranty  conditions.  Prebena  Company  guarantees  free  removal  of  malfunctions  associated 
with defects of materials or manufacture. Violations of function or malfunction associated  with the incompe-
tent use within the free warranty shall be disregarded. 

In addition, you should use only original mounting technique of company Prebena, in case of non-
compliance of this condition warranty from the manufacturer does not work, and thus warranty requirements 
are not possible. The warranty does not cover consumables, such as, for example, o-rings, etc. The compa-
ny Prebena has the right in its sole discretion to decide the question of providing warranties in the form of 
replacement of defective components or the provision of other compressor. Submission of other claims is 
impossible. 

For  presentation  of  the  claim  to  execute  guarantees  it  is  necessary  to  present  a  fully  completed  warranty 
card stamped by the seller and  with the date of sale, or supporting document attached to a  bill  which con-
tains the dates and details in accordance with the warranty card. 

Shipping:  defective  device  must  be  carefully  packaged  and  sent  to  the  address  of  company  Prebena  with 
postal charge prepaid. 

 

The warranty card 

Model: 

Date of purchase: 

Seller: 

(stamp) 

 

Summary of Contents for VITAS 45

























Reviews: